Return to the Electrical Wiring Forum | Post a Follow-Up

 o
wiring a boat dock to connect to generator

Posted by lectricn00b (My Page) on
Sun, Jun 8, 14 at 10:32

Hi All,
I've been browsing and reading this forum and decided to create an account and post here. Hopefully I can get the assistance I need to successfully complete my project...

I have a small boat shelter and dock area on a piece of land that has no grid power currently available. I've been running my boat lift, power tools, and battery chargers from an 8500watt generator when I need them. I would like to move away from that extremely loud rig so I can wire up a stereo, a few lights and a ceiling fan.

A few extra details:
-One day when I build and bring in grid power, I will hook this up to the grid and supply the panel from there
-I have some leftover items that I would prefer to use if they are appropriate but will use what I 'should' use to be ready in the future
-The generator I would like to move to (haven't bought yet) is either a Yamaha 2400ishc or similar (2kw range inverter generator)
-My boat lift circuit is rated for 1.8kw max and the motor surges to 1.5kw on startup
-I have not bought lights yet but would spend extra on lower power lights to allow me to utilize ~2kw inverter generator
-I have already decided on the ~2kw generator and would like to design this interim (several years) solution until I build and can bring in grid power

I currently have (but will buy whatever is appropriate):
-a spool of 10/3
-a spool of 12/2

My first draft plan (looking for help here)
-8' ground rod at the shore to a power inlet box (essentially at a stub up where I can connect to the grid in the future)
-30amp power inlet box
-run 10/3 with red capped off since I'll be connecting my 120v generator to a power panel
-6 breaker power panel with 1 or 2 15a or 20a breakers installed (1 for the lift and 1 for the radio and a few lights)

Swapping between my 8.5kw generator and a ~2kw generator is not trivial so I think if I need the 240 for anything I will simply use the outlet in the 8.5kw generator.
Looking for advice all around on this. Thank you!


Follow-Up Postings:

 o
RE: wiring a boat dock to connect to generator

You may wish to get a copy of the NEC and read up Article 555. Make sure your boxes, etc... are fully gasketed watertight. Make sure all exposed metal is grounded. Make sure that any cordage used is appropriately rated (including SUNLIGHT and WET LOCATIONS). Make sure you provide GFCI protection.

If you have are installing a shore power line to the boat it must be at least 30A.


 o
RE: wiring a boat dock to connect to generator

Hi ronnatalie- I checked 555 and am not sure that I was clear what I am wiring to. I have a private boat shelter on a private lot that has a boat lift currently (that I power with a generator). NEC 555 appears to cover a much broader and more commercially oriented setup but seems rational overall.
I have a couple of questions:
-What is the recommended wire to run from a 20A GFCI breaker to an outlet in a boat shelter? Is it supposed to be something like underground feeder wire?
-Any ideas for getting that 8' ground rod into the ground when I have no water (really liked the hose connected rod approach I saw on youtube)?
-Is the code saying that I need to have those plastic covers over EACH outlet box even if it is covered if it is less than 8' from the floor level in the dock?
-same for the switches--is there a special type of one that is appropriate for this?
-When I did my hot tub (another property) I used a hot tub disconnect box near the hot tub. Is something like this suitable for the stub up on the shore where I plan to plug in my generator to power the line down the dock to the panel?

It looks like my existing wiring is of no use in this install -- figures :)

Thanks for the help.


 o
RE: wiring a boat dock to connect to generator

You need to use 12g wire most likely but in a cable or conduit that is approved for wet locations as well as sunlight.

Big hammer (or the rod slamming tool).

You need to use the appropriate waterproof boxes. If you're likely to leave things plugged in, you need the in-use cover.

Despite how much you don't think you have to comply with 555, you do.

They make waterproof enclosures that work an internal (traditional) snap switch.

Again, you must use wet rated boxes for everything.


 o
RE: wiring a boat dock to connect to generator

Got it. I'm on board with 555, not just because it's the code but because it's hard to argue against it -- it makes good sense and I want my work safe.

So now for the part about hooking up the generator:
What'd I'd like to do is at the stub up near where the dock meets the shore, I'd like to put in the power transfer box. Someday, when I build a house I will replace it with power from the grid; today I would like to just put in a box to power from a quiet generator.
-If I put in a 30A power transfer and run 10gauge to the breaker box (that I have yet to buy or install) is it appropriate to use only 3 of the wires (white black ground) and cap off one for eventual use with grid power?
-The reason I want to do it that way is so that I can run the wire once and use it later when I get more power. Alternatively, I can put the gennie on the land and just run an extension cord but then there's a cord running down the dock.
-What is your recommendation on power transfer?
-What is your recommendation on the size of the breaker panel (I am planning on 100W of lighting, a stereo of say 200W, a ceiling fan ~150W, and my boat lift 1.5kw to start and not sure the operating load--will need to use my killawatt)?
-My thoughts were to buy one that would house 4 breakers: 1 for electrical outlets, 1 for lighting and fan, 1 for boat lift, and 1 unused.

I'm not looking forward to beating the grounding rod into the ground though.
Thank you!


 o
RE: wiring a boat dock to connect to generator

Pay attention to the power factor of any non-incandescent lights. Poor power factor "energy saving" lamps are all over the residential market. You don't pay for the extra power that they use, compared to good power factor stuff when using grid power, but your genset will notice. Commercial fluorescent and LED lamps have a good power factor. (1 is a perfect power factor. 0.9 and up are good whereas 0.5 is crappy.)

Got rocky ground?


 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!


Return to the Electrical Wiring Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Please review our Rules of Play before posting.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.


Learn more about in-text links on this page here