Return to the Home Repair Forum | Post a Follow-Up

How to repair dry rot on ends of exposed beams?

Posted by cathyinbothell (My Page) on
Sat, Sep 12, 09 at 22:15

My husband and I own a small A frame 30 year old cabin that is close to the water. The cabin is a typical A frame, with huge beams that support the roof and go from the inside and extend outside a few feet. We started noticing some dry rot at the end of the exposed outside beams last year, (these are about four feet off the ground) and this year it has really progressed. We can stick a screw driver in the end up to six or more inches. Should we cut the neds of these beams off and attach new wood somehow? Or should we fill the rotted ends with something and cap them or are there other options? Any advice would be appreciated,


Follow-Up Postings:

RE: How to repair dry rot on ends of exposed beams?

I am no expert, just a DIY. I had some spots outside with some rot (wet rot and some dry rot) I repaired. I removed all the bad wood and let it dry for at least a few good hot dry days so any moisture was gone. I think I also sprayed it with some bleach to kill any mold spores, I think you can use borax solution also. Applied wood hardener (minwax makes some)it makes the wood harder if it is a bit soft. Then used wood filler (not wood putty) It drys pretty hard. Then I primed and painted it. Its been a few years since the repair and it seems to be holding up. I probably should have sanding it a bit more where I used it but it's not in a area really seen.

RE: How to repair dry rot on ends of exposed beams?

Do these ends stick out beyond the roof line so that they are exposed directly to the elements? And is any of the damaged stuff structural (meaning the rotted area is directly supporting something)?

RE: How to repair dry rot on ends of exposed beams?

Can't say without a photo.

RE: How to repair dry rot on ends of exposed beams?

Whatever your solution, be advised that dry rot needs complete removal lest it begin anew on any wood attachment.
I personally do not know whether bleach or mildewcide is effective. Chlorine/hypochlorite has destructive properties in:re wood besides most other materials.
As Macv says, hard to say without a photo, but presumably the tails though part of the load bearing member would be less loaded and amenable to splicing.

RE: How to repair dry rot on ends of exposed beams?

I agree with previous post - after applying wood hardner ( I use the Minwax) let it dry for a day. As for a filler, I use regular Bondo. I then sand smooth and prime and paint.

RE: How to repair dry rot on ends of exposed beams?

In general, it's best to remove as much damaged wood as possible, and replace it with a paste EPOXY, like PC-Woody (strong, wood-colored), or PC-7 (very strong, but gray), or PC-Concrete or Simpson Strong-Tie ET/SET anchoring epoxy (KILLER strong!... but concrete gray color).

Beware of Bondo and similar auto body fillers. They are made to be sealed with paint, and will soak up a LOT of water if they are left unpainted.

A bleach solution WILL kill everything IT CAN GET TO in wood, but TSP (tri-sodium phosphate) will enhance the process by making the solution "wetter", and thus able to penetrate deeper, and GET TO more rot. Most brands of TSP will have recommended proportions of water, bleach, and TSP on the box. TSP is sometimes marketed as "Deck Cleaner" in order to boost the price of this simple chemical.

As for the Minwax wood hardener, it might be OK, in some apps, but it's pretty lame compared to the LOW-VISCOSITY EPOXY RESINS designed for the task of soaking into wood, consolidating the loose stuff, and then curing into... epoxy. ;')

There's "PC Rot-Terminator" from PC Products, available on, and "RotFix" from System Three, available at Woodcraft stores. It's not cheap.

With any epoxy product, THOROUGH mixing of the 2 parts is essential to success.

Here is a link that might be useful: Some useful info/video on rot and products...

 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!

Return to the Home Repair Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Please review our Rules of Play before posting.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.

Learn more about in-text links on this page here