Return to the Home Repair Forum | Post a Follow-Up

Suggestions for fascia material

Posted by surfer (My Page) on
Sat, Aug 4, 12 at 14:45

I'm looking for a low maintenance material that could be used as a 12" by 16 foot fascia on a gable end considering the dark brown color rules out PVC material like Aztek. Actually I have two gable ends, one east and one west.

My current fascia material uses two painted "one by" 16 foot wood boards on each side. It faces mostly west. The top board is about a 1 by 5" and the lower is a 1 by 8. The total finished width of the two boards side by side is about 12 1/2". I could probably get by with 12" width. The current arrangement requires regular maintenance and painting. The wood seam between the two boards is caulked but it still eventually allows water to get behind the fascia.

I considered wrapping with aluminum but the width and dark brown color facing west would probably cause some waviness. Also the 16 ft aluminum would still be pieced and overlapped.

Another consideration is using smooth finish 12" by 12 ft fiber cement. It would require piecing too to cover the 16 foot length, and the required butt joint cuts would be at 45 degrees bevel and the pieces cemented with the long side facing down. Thanks for any suggestions.

Here is a link that might be useful: Photo of gable end

Follow-Up Postings:

RE: Suggestions for fascia material

A paint job should not require annual painting, caulking either.
If you are not treating the end grain of 1x trim with Wood hardener or epoxy to prevent water intrusion you are never going to get a god paint job.

5/4 trim is beter, and if the width is as large as you say, even 2x shold look fine.

The thicker boards require end grain treatment also.
You should glue the wood together at the joiny, not rely on caulk to try and seal it.

A coat or primer brushed on all surfaces, and two coat of paint brushed on all surfaces before installation should last at least 5-10 years.

As you have found out, the large with is likely to play havoc with man made materials.

RE: Suggestions for fascia material

Thanks for the reply. Have you or anyone had any experience with MiraTec? My concern with any joints whether they be longitudinally or as cross ways is separation and water intrusion due to expansion and contraction, and the obvious appearance.

Here is a link that might be useful: MiraTec

RE: Suggestions for fascia material

You just slide the trimmed edge of the fascia panel into the under-sill trim. Draw a line where the panel intersects with the trim.

RE: Suggestions for fascia material

@Aaronjohn.....Did you mean to post this as a follow-up on another thread? Not sure if I am misreading this. Thanks.

RE: Suggestions for fascia material

Why not use Aztek? It can be painted any custom color.

Instead of trying to make what you have work, consider removing the two pieces or wood and then replace them with a 12" wide board (or 14" ripped to size).

Here is a link that might be useful: FAQ re: paint

RE: Suggestions for fascia material

Buy a 4' x 8' sheet of azek, cut to pcs 8' long 16" wide and screw it in place and paint.

RE: Suggestions for fascia material

Appreciate the feedback. I'm planning on using 4/4 x 16" x 16' primed Miratec. Got a sample and discussed with those that have used it and did some reading on discussion forums such as this
Cost wise it about 2x clear pine that is only 11.25" wide.

Azek does not like darker colors because of heat absorption on PVC. Also it is much more expensive.

 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!

Return to the Home Repair Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Please review our Rules of Play before posting.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.

Learn more about in-text links on this page here