corner drawer pulls

10 years ago

I've had corner drawer built for my new kitchen and am trying to find drawer pulls that will prevent me from having to have two pulls facing each other for each drawer and instead have one pull that has each side of the pull on each side of the corner. I hope that makes sense.

I haven't been able to find any beyond this picture

http://www.instructables.com/id/Homemade-kitchen-corner-drawers/

Anyone out there found any? I'm looking for brushed nickel, but at this point, I'm just looking for a general direction to pursue.

thanks,

Jennifer

Featured Answer

annzgw

10 years ago

If you can find a handle that is the right length, you may be able to get someone that works with metal to custom bend it for you.
Just be sure to leave enough room for your hand to grasp the handle.

In the pic below it appears the cabinet maker recessed the ends of the handle into the front of the drawer.

Here is a link that might be useful:

Sort by:Oldest

Comments (11)

kirkhall
10 years ago
Maybe check over on the kitchen forum?
Related Professionals
North Druid Hills Kitchen & Bathroom Remodelers · Beach Park Kitchen & Bathroom Remodelers · Citrus Park Kitchen & Bathroom Remodelers · 93927 Kitchen & Bathroom Remodelers · Islip Kitchen & Bathroom Remodelers · Kettering Kitchen & Bathroom Remodelers · Southampton Kitchen & Bathroom Remodelers · Forest Hills Kitchen & Bathroom Remodelers · The Crossings General Contractors · De Pere General Contractors · Dorchester Center General Contractors · Greensburg General Contractors · Montclair General Contractors · Rolling Hills Estates General Contractors · West Babylon General Contractors
bpath
10 years ago
Just wondering, is there any rule that says the screws MUST go into the drawer completely perpendicular? Maybe you could angle the posts and install the screws on the appropriate angle?
hhoffe
3 years ago
I have the EXACT same issue! Been looking and inquiring and have had no luck... I can't believe there aren't any out there with corner drawers gaining in popularity! We've been living with no handles and I plan to until a smart knob/pull manufacturer makes one!
hhoffe
3 years ago
OMG and this is from 7 years ago!?!?! Still none are out there?! I came across the same pictures as posted above!
Lisa Adams
3 years ago
Any luck anyone? Our cabinet maker wants us to put a handle on each side, and it’s so ugly!
Helen Courtney
2 years ago
I'm in the same boat...the year is 2022 now...
hhoffe
2 years ago
Whoa, no way... So odd! Cannot believe these are still not manufactured. We still have no handles and grip the top and bottom to open them -- which we would not even be able to do if our door faces were flush!
ci_lantro
2 years ago
last modified: 2 years ago
hhoffe
2 years ago
Oh nice— were those manually bent or manufactured that way? our drawers and pulls have 90’ square corners… these drawers are unique with curved corners, wow wow!
ci_lantro
2 years ago
last modified: 2 years ago
Don't know but would guess the pulls were custom bent after purchase.

That type of stainless TBar pull is available in both solid bar & hollow tube. I would take a photo to an auto brake repair shop & ask if they could bend them & which (solid bar or hollow tube) would be better for bending. Guessing they will say hollow tube.

Brake repair place because I know that they have to bend stainless steel brake lines so would have the tools--except brake lines are smaller diameter. If not a brake repair place then a shop that repairs hydraulics (big trucks/ tractors....)

The pulls are quite inexpensive on eBay so I would buy extras. (Pieces to practice on.) A casual look-see on eBay--most of the offerings are 'solid bar' but there are some hollow tube ones also.

Just re-read the posting--and that you have pulls. So bending those is probably not an option. Would likely break.

Un obtrusive finger tab pulls in a matching finish perhaps?