Return to the Plumbing Forum | Post a Follow-Up

 o
galvanized pipe replacement by copper AND pex - how to plan?

Posted by elphaba (My Page) on
Mon, May 20, 13 at 10:33

Our house is 80 years old and has pier and beam foundation. We will probably/hopefully live here another 10 years but it could be a "tear down" when we decide to sell. We are in a very good neighborhood (maybe too good for our humble little house). So not sure what our priorities should be as far as pace and pathway to replacing galvanized with PEX. Our water pressure seems to be fine. We are considering whole house water filtration to eliminate chloramine but that is another topic.

Read somewhere on the web that an optimum PEX installation is for each fixture to have a direct line using PEX with minimal number of places where the PEX is broken into from where the water enters the house. (reason to use manifold?) This helps water pressure but also, something that sounded more serious were comments about "leaks" at intersections?

Should we be concerned about minimizing intersections to optimize performance of plumbing fixtures and to minimize potential for leaks or is just okay to have as our goal to replace all galvanized? (not sure if we will have a manifold if we proceed the way we are going.)

I will cross-post this in the OLD HOUSE forum - may be more relevant over there. Not sure.

background/details:

Our old galvanized pipe system is being gradually replaced. Pipes in our newly remodeled bath were replaced with copper. An incoming line from the city to our new external tankless gas water heater was installed with PEX so water would be "clean".

Newly remodeled bathroom copper plumbing is connected to galvanized "network" and then to PEX. I wasn't in a great hurry to fix this as we proceed to remodeling our second bathroom (and then onto kitchen) but now I'm wondering if my phased approach is a bad idea. .
Our remodeler/plumber doesn't do pex so won't have the copper in either bathroom connected to pex plumbing "network" yet - still tied into galvanized to some extent - there is a fair amount I can't explain except to say that I know we must address need to connect PEX somehow (with an adaptor/manifold?) to copper.

I haven't got the right plumber yet for the pex. I had planned to take care of this when we get to the kitchen which is the last phase that involves plumbing. Is it important that I get PEX "interface" done sooner rather than later and at that time, design the plumbing to minimize intersections?


Follow-Up Postings:

 o
RE: galvanized pipe replacement by copper AND pex - how to plan?

I suspect all of your (good) questions are as puzzling for you as they would be for any average homeowner, and are probably trivial everyday factors for an experienced plumber.

I suspect your questions could be answered and problems addressed if you can find the right plumber. I'd focus on that and then let them do the job the right way.


 o
RE: galvanized pipe replacement by copper AND pex - how to plan?

I'm doing the same at my home now. I am going pex all the way, except for the stub outs for the fixtures. Pex to copper is fine, but I would suggest that you eliminate the galvie entirely. You do not have to run the "home run manifold system". With my lay-out it is better. YMMV. You can pipe it conventionally. What I like about the manifold system for me is that I am running small diameter tubing to each faucet. That means I will not have to wait as long to get hot water to a faucet. If you look at the cross sectional area of 1/2, 3/4 and 1" tubing, they are .19, .44 and .77 sq in respectively. That all equates to volume that you have to move out before you get hot water. Just something to think about.


 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!


Return to the Plumbing Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Please review our Rules of Play before posting.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.


Learn more about in-text links on this page here