Return to the Plumbing Forum | Post a Follow-Up

Water Softener Sizing Check

Posted by rlembke (My Page) on
Wed, Feb 27, 13 at 23:39

Hi guys -

Long time lurker, searcher and student of the many helpful folks here in the plumbing forum. Thank you all for your great contributions.

I'm finishing our home's basement and while doing the plumbing I want to add a water softener. I have heard great things about twin tank units and would prefer one if the numbers work. Currently looking at the Fleck 9100SXT with 2 x 1cf.

- 5 bed/4 bath w/ jacuzzi tub (rarely used)
- 2 adults, 2 kids, occasional family guests
- 2 dishwashers, washing machine
- SFR of 9gpm (measured at jacuzzi)
- 3/4" service
- irrigation will be with untreated water
- city water (all levels from 2012 report)
- hardness total = 188ppm max
- iron = n/a
- manganese = n/a
- pH = 9.1 - 9.8
- Alkalinity = 85ppm max
- TDS = 412ppm max
- Sulfates = 216ppm max
- Chloride = 100ppm max

The water here isn't terribly hard but every time I visit family with a Kinetico system, I dream of soft water. The usual white or green buildup on every faucet is getting old also.

Planning to do this DIY. I'm a mechanical engineer and I appreciate knowing things are done the right way while being smart with the $$.

I've been looking at Ohio Pure Water and have noted many of the usual items I need to request (Noryl bypass, top basket, gravel underbed, Purolite resin).

Thank you so very much for sharing your knowledge with the rest of us faceless lurkers!


Follow-Up Postings:

RE: Water Softener Sizing Check

How low can you go on the salt dosage with a 1.0cf tank? 4lbs/cf would give a 16000 capacity, correct? Even at that capacity, I'm still looking at 10 days per regen per tank, right?

4 people x 75 gallons x 11 grains = 3300 grains/day
3300/16000 = 4.8 days/regen = ~10 days/regen each tank

I imagine as with most things, when you are working near the min or max of efficiency in one area, you're losing efficiency elsewhere.

RE: Water Softener Sizing Check

You could go with a twin tank system at 1 cuft each, but I am curious as to why you want a twin tank system. Do you use water 24/7? :Unless you do, it is not likely worth the extra expense. Particularly when you have a jacuzzi tub, you would be better offer getting a single, slightly larger softener so you can get more flow to your tub without hardness bleed.

75 gallons per day per person is a bit high. Is this metered or a guess on your part? Generally 60 gallons per person per day is closer.

Your pH is crazy high, particularly for city water where they should be sending out water closer to neutral pH. I always recommend homeowners have the water in their homes tested because water can pick up a few things on its way from the city. In your case, this is not just recommended, it is absolutely necessary because of the high pH water. You need: TDS, pH, iron, manganese, hardness, alkalinity, chlorine (or chloramines - ask you city which you should expect to see), copper (not something we normally check for, but the high pH dictates).

Capacity: At 4 lb salt per cuft, you should see around 18,000 grains per cuft capacity. The tradeoff for lower salt dosage is more hardness bleed and more frequent regeneration. It also places your softener pretty close to minimum dosage, so is not generally something I recommend. The sweet spot between salt efficiency and water efficiency, while maintaining good softener operation is at 6 lb salt per cuft of resin.

This post was edited by aliceinwonderland_id on Fri, Mar 1, 13 at 15:51

RE: Water Softener Sizing Check

Alice -

As I spend more and more time 'checking' my logic and math by looking at previous homeowners' requests for assistance, I think I realized the twin tank option just isn't a good one even before you confirmed it. Let's lay that option to bed.

I've also seen the 60 gal/person number used more often and started recalculating based on that. I haven't checked our actual usage but I will check that tonight. But using 60gal/person as a starting point, that puts my target 7-day regen needed capacity at 18500g (assuming the pH doesn't factor in). I'm guessing you're saying my SFR should be higher than just the demand of the jacuzzi. How much larger of a unit would you recommend to handle my SFR?

Here is a link to our utility's water report: Files/2012-AnnualReport.pdf

Regarding the pH, I was a little startled to see that high of a number as well. The report lists federal guidelines of 8.5 but then show they are trying to achieve >9.0. Is the pH something we should deal with?

Any recommendation for places to do water testing? I'll start looking locally in the meantime.

RE: Water Softener Sizing Check

This test looks like it will check everything I need. Any other recommended labs?

The water district says it uses chloramines to disinfect - will chloride testing detect that?

RE: Water Softener Sizing Check

Actual winter water usage has averaged around 140 gal/day over the past few years. Our two sons are only 7 and 4 so that will increase in coming years.

RE: Water Softener Sizing Check

The test you linked looks fine.

Chloride testing will not detect chloramines. You can get that information from the city - if anything, chloramines will decrease a bit on the way to your home.

RE: Water Softener Sizing Check

Found another lab that was well respected on a home brewing forum, very reasonable and in the Midwest. Samples sent off this morning so I should have results by week's end.

The water district's quality report lists chloramines as 1.4-4.3ppm, average of 3.0ppm.

RE: Water Softener Sizing Check

Water test results back from Ward Labs

pH 9.5
TDS 388
Cations/Anions 6.2 / 6.7
Sodium 75 ppm
Potassium 7 ppm
Calcium 28 ppm
Magnesium 17 ppm
Total Hardness 141 ppm
Nitrate 0.6 ppm
Sulfate 53 ppm
Chloride 56 ppm
Carbonate 20 ppm
Bicarbonate 68 ppm
Total Alkalinity 89 ppm
Fluoride 0.61 ppm
Total Iron <0.01 ppm
Manganese <0.01 ppm
Copper <0.01 ppm


RE: Water Softener Sizing Check

Your hardness is relatively low, which would place you at a 1.0 cuft softener. However, with your jacuzzi at 9 gpm you should go with a 1.5 cuft softener to ensure adequate softening for your flow rate.

I am a bit concerned with your pH. If I were you, I would get some test strips and check pH periodically. Most resins will operate up to the 9.5 - 10 pH range, placing you pretty close to max. Just monitor it for now.

When you look for your softener, you want the following:

1) 1.5 cuft softener
2) High quality American or German resin (better size distribution), standard mesh
3) 10% crosslinked resin. This will be more expensive, but the extra crosslinking will make the resin more resistant in the oxidizing environment of city water.
4) top distribution basket
5) gravel underbed
6) valve with metered control, such as Fleck 5600sxt or equivalent Clack valve
7) noryl bypass
8) plumb the softener in with a bypass so that it can be blocked in without disrupting water flow to your home
9) BLFC (brine line flow control) 0.5 gpm or smaller. This is not typically an issue, but it's a good idea to verify.

RE: Water Softener Sizing Check

Thanks again for the advice, Alice.

How concerned should I be about the high pH? It seems pretty obvious to me that most of the deposits we see are due to the high pH and not necessarily our not-very hard water. What options are there for treating high pH - both whole-home and drinking water? I'm a little worried about what happens if I monitor the water and I reach that 10 or higher level.

So a 1.5 cuft unit, dosed at 9 lbs/regen will give a capacity of around 30000g, right? But I only need 18500g over a 7 day period. I'm curious what you'd recommend for the efficient settings, including regen time. If I didn't worry about the jacuzzi SFR, would I need to be concerned with SFR due to the number of bathrooms anyway?

RE: Water Softener Sizing Check

Alice - any other comments? Anyone one else have any input to add?

I'm curious about the final settings for regen.

What are options for addressing high pH? I'm not finding much in this area.

I see the Purolite SST-60 resin says it operates in all pH levels. That's the only US 10% resin I see from OPWC - is that the one to pick?



RE: Water Softener Sizing Check

A 1.5 cuft softener regenerating at 9# salt per cubic ft would give you a capacity of 38,000. However, there is no need for you to regen with 9# since you do not have iron in your water. The sweet spot between water efficiency and salt efficiency is at 6# salt/cuft resin, which would place you at 31,000 capacity. We could regen yours as low as 4#salt/cuft resin, for a capacity of 27,000

I you don't mind hardness leakage when filling the jacuzzi tub, you could go as low as 1.25 cuft, but I wouldn't go any lower for the fixtures in your home.

pH: A chemical injection system, consisting of a tank, controller, and chemical feed pump will take care of the problem. Either acetic acid or citric acid with alum will work. Some systems use sulfuric or hydrochloric acid but those are much more aggressive acids and typically used if water pH is 11 or higher.

Resin: SST-60, while a very good resin, is overkill for you. Yes, it has great chemical resistance capabilities, but it is also neutral-core resin, most suitable for iron-laden waters and much more expensive than other resins. There are other 10% crosslinked resins and other companies from which to purchase a softener. Just to name a few resins: Purolite c100x10, Dow HGR, Rohm and Haas IR-122

RE: Water Softener Sizing Check

1.5 cuft Fleck 5600SXT unit ordered, delivered and installed! I walked through the manual regen process as has been outlined before to make sure the resin is rinsed well and backwash is clear, brine draw and fill all working properly.

Here are my first stabs at the settings. Let me know if I've missed any:

VT - Df1b
CT - Fd
NT - 1
C - 27
H - 11
SF - 20
DO - 10 (?)
RT - 2:00
BW - 10
BD - 60
RR - 10
BF - 4

BLFC is 0.5 so the BF is set to regen with #4/cuft or #6 total.

Am I ready to roll? Thank you again for your help! Can't wait to feel the new water!

RE: Water Softener Sizing Check

Alice -

Just need a quick review, please. Thanks!

RE: Water Softener Sizing Check

I was vacationing with no phone/internet access so did not see your post until this morning.

You settings look good.

RE: Water Softener Sizing Check

Thanks Alice! My family and I are grateful for your advice and council.

God Bless

 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!

Return to the Plumbing Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Please review our Rules of Play before posting.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.

Learn more about in-text links on this page here