Return to the Metalworking Forum | Post a Follow-Up

Building a galvanized pipe firemans pole for treehouse

Posted by lsst (My Page) on
Fri, Sep 18, 09 at 10:31

Has anyone on this forum built a fireman's pole out of galvanized pipe? If so, what diameter pipe and how did you construct it?

My husband and I are building a free standing tree house and we would like to add a fireman's pole on the outside.
We did an internet search but what we found are for outdoor play sets and are too short.

We plan to cement a 1 1/4 or 1 1/2 inch diameter pipe into the ground and have it go approx. 16 feet into a 90 degree angle at the top. The top will be attached to a threaded flange that is attached to the roof header.
We were hoping to use threaded galvanized pipe with a 90 degree elbow.

Would it be better if we had a steel company fabricate and weld it instead of using threaded parts to connect it all together? Can galvanized steel be welded?
Thanks in advance!

Follow-Up Postings:

RE: Building a galvanized pipe firemans pole for treehouse

I'm not a welder but seems like I remember galvy being difficult (read impossible)to weld. Also seems like a 16 foot length would be a little more difficult ot obtain. I think the home improvments stores usually only carry 10 foot lengths.

A steel shop should have some sort of stock that'll work and they prolly could thread the top end for receiving an elbow to eliminate the welding. Wouldn't go with plain steel due to environmental reasons (rust). A good paint might help there though.

Also if this is for sliding, threaded unions for connection would prolly remove chunks of flesh each time down. I'd think you'd want a continuous piece of something sturdy and smooth (welds even when ground smmoth would be rough and this would also be hard to achieve on a round pipe). On that note the galvining process sometimes leaves surface imperfections that could slice flesh too, not so much on OD of pipe but on dipped items I've handled before seems there were little points and protrusions from the dipping process on edges and such.

Most of the fire poles I've seen are brass but I'm not sure how it would weather. I would think it would require care since the copper content would cause a patina.

a steel shop should have all kinds of stock that would work. I'd think you'd want about 1.5" not for strength but for ergonomic reasons. anything smaller might be hard to grab depending on how big your kid's hands are....maybe smaller would be the way to go if it doesn't bow.

Not trying to be crass, but you may want to look into a "stripper pole". They would be smooth, similar length, and obviously the right strength. Could be a cheaper alternative to a custom stainless rod from a welder's supply house.

RE: Building a galvanized pipe firemans pole for treehouse

Thanks for the reply!
If I can get a 20 foot pole and have it cut down, where I put the elbow should be above the smooth slide area.
I am thinking 3 -4 feet in the ground then 16 feet straight up- then a 90 elbow with a 2 foot piece and flange to connect it to the header. I might have to have the pipe cut about a foot.
I looked into a "stripper pole" but they are so expensive and I still would need to get a 90 degree elbow on it to attach it to the tree house.
I think I will go to a steel supply place and see what is available that will not break the bank! LOL
I would love to have a piece of steel or iron either welded or "rolled" for the 90 degree curve I need.
If I use steel or iron instead of galvanized, I thought about having it welded or rolled and then prime and paint it.
I have no clue what it would cost though.

Here is a photo

Here is a pic of the shape I need.

RE: Building a galvanized pipe firemans pole for treehouse

Pipe comes in standard lengths of 20' when threaded (TBE) or randoms of 20-21' when plain end or beveled, so your dimensions would enable a 90deg. bend, thus eliminating any welding, which would burn off the protective galvanising.
A muffler shop may be able to do the bend- I presume you would use Sched.40 pipe.
A welded pipe fitting would allow a tighter bend radius if needed, but joints would need proper finish coats.
Plain steel (black pipe)isn't a bad idea; there are some very durable urethane coatings available.
I would not place the pipe in concrete, but use a bolted flange base plate. Condensation corrosion on the inside of the pipe will eventually cause failure at the pipe/cement juncture.

 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!

Return to the Metalworking Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Please review our Rules of Play before posting.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.

Learn more about in-text links on this page here