Return to the Metalworking Forum | Post a Follow-Up

Intricate cuts in sheet metal

Posted by plateaugal (My Page) on
Wed, May 27, 09 at 17:14

I am a complete novice, so please forgive my ignorance. I want to make some intricate curved, and clean cuts in fairly thin sheet metal. What hand or pneumatic tools would you recommend? Would a Dremel with the right attachment be helpful? I have a pneumatic metal cutter, but it is best for straight lines.

The first photo shows copper foil pressed over a worn out push plate. I glued it to the back, and now I want to cut a clean edge so I can then screw the finished plate onto the door, and hope no one realizes it is not plated. If I can just cut the curve and get rid of burrs, it should be fine.

The second shot is an arch to reduce the area of my fireplace opening. I have hopes it will cure the smoking fireplace problem. It will also be covered in copper foil. First, though I just want to smooth out the curve a bit at the two "corners" at the end of the arch.

I bet there is something out there that will do the trick for both jobs.

Here is a link that might be useful: Remodel

Follow-Up Postings:

RE: Intricate cuts in sheet metal

1. Aviation tin snips will do most anything you could imagine. A bit of a learning curve, and the cuts may need some subsequent file work.

2. A pilot guided,flush trim, carbide tipped two or three flute router bit will work in a router or better, an air die grinder. Smooth, though slight scalloping may be seen on edges, depending on skill of operator. DO NOT use these on steel!

3. 1/4" shank carbide burrs work very well in a die grinder. They eat steel.

I don't have the time to type out 15 pages of why this is potentially hazardous. You realize anything sharp could cut you, anything rotating has its own dangers, you shouldn't run with scissors, it WILL put your eye out! tiny sharp copper swarf will fly everywhere with rotating tools ( which is why air powered is superior here, no motor armature, brushes etc.) If you don't clean up or contain, the chips will be EVERYWHERE.

Different snips and a collection of files could do all you want at a peaceful quiet pace.

RE: Intricate cuts in sheet metal

I will try snips and files. Bondo is on hand for errors in the second project. Thanks for the safety warnings. I will also get a metalworking kit for my Dremel and a pair of safety goggles for the first project.

Many thanks.

RE: Intricate cuts in sheet metal

I routinely do fairly intricate cuts in galvanized steel sheet metal in gauges ranging from 20ga (0.0396") to 8ga (0.1681") and as Alphonse said earlier, my primary tools of choice are aviation snips.

Having said that, it must be noted that not all aviation snips are created equal, and you can expect to get what you pay for.

In the sheet metal trade the aviation snips of choice are made by "WISS". You can expect to pay about $15 to $20 for each snip but they are well worth the cost.

When examining aviation snips you will note that there are three colors on the handles, RED, GREEN & YELLOW.

Red snips are properly called "Left Hand snips" because they are designed to cut straight or a curve to the left.

Green Snips are properly called "Right Hand snips" because they will cut a straight line or a curve to the right.

Yellow snips cut a straight line.

If you are right handed you will find the RED's (left hand snips) to be the tool you use most often because it keeps your guideline on the left side of your hand where it is easier to see. (If your left handed the Green's would be easier to work with).

When working on ductwork we often have to cut through a folded seam that may be as much as 4 layers of the sheet metal. In this case we use a pair of "Bulldogs" which look like a pair of Red's with short stubby jaws.

The real secret to quality cuts is a fine layout line. Traditionally a metal scribe or Scratch awl is used to
mark your layout line by making a fine scratch on the metal.

Generally in the trade we don't use the Yellow snips much because both the Red's & Green's will cut a straight line.

RE: Intricate cuts in sheet metal

A nice precis on snips, that.

RE: Intricate cuts in sheet metal

As far as the smoking fireplace, that sounds like your house is too tight and the smoke is rolling out. Try cracking a window while burning and see if that stops the problem. If so you may want to consider installing an outside air intake for yout fireplace.

 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!

Return to the Metalworking Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Please review our Rules of Play before posting.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.

Learn more about in-text links on this page here