Return to the Laundry Room Forum | Post a Follow-Up

 o
Kenmore HE3 dryer motor - repair?

Posted by jacy (My Page) on
Sat, Sep 14, 13 at 19:31

I'm fairly certain I've diagnosed that the motor on my Kenmore HE3 is shot. I have the HE3t washer as well, very early models. I've been pretty handy with them so far (I'm on my fourth thermistor and I replaced the pump on my HE3t washer and something else I can't recall) but after a YouTube/Google run on the motor replacement I think I might be in over my head. Plus, they're stacked and it's just me and my daughter.

I'm imagining a service call would prove to be one-third to half the cost of a discounted replacement, given the labor and markup on the motor? Additionally, I took a fair amount of water in my basement this summer and while the washer hasn't seemed to suffer, it was nevertheless 8" deep for a few hours so I wonder. Every now and then a sizable dribble of water will run from beneath the washer.Can't figure the common denominator on it - very random so far.

So, pay to have the dryer motor replaced (probably due for a thermistor soon, too) and keep my fingers crossed, or bite the bullet and replace both units with a new stacking pair?

These were scratch-and-dent models back in the day and I'd try to replace with same. They're in my basement laundry room, I couldn't care less what they look like. I would probably invest in a steam dryer replacement - I love to fluff and dewrinkle with a wet towel. Not so sure about a steam washer. I can get by with cheaper models, I'd think.

Any advice? Are these nearing the end of their lifespan?


Follow-Up Postings:

 o
RE: Kenmore HE3 dryer motor - repair?

Dryers typically have double the service-life of washers, if not longer. My parents dryer is 19 years old and has had only one service incident, replacement of a thermostat. A friend gave a 35-years-old Kenmore dryer to me a couple years ago that they were going to toss out. It was "slow" so they thought the heating element was going bad (elements typically either work or not, they don't wear out and get cooler). I found the airflow was obstructed due to being clogged with lint (the handle on the filter was broken). I replaced the filter and rear drum seal that had a small tear, cleaned it up and sold it for $80.

Replacement of the motor requires full disassembly but is not a difficult job ... notwithstanding pulling down your stacked unit, which will likely add some labor cost for a servicer to do it.

You can look up the model number at SearsPartsDirect.com to check what's the ballpark price of the motor, with the understanding that price doesn't reflect what a servicer will charge (there are numerous online parts sources, Sears may or may not have the lowest price for a DIYer).

The serial numbers are coded for the year and week of manufacture. Answer back here with the serials if you'd like to know that info.


 o
RE: Kenmore HE3 dryer motor - repair?

Thanks for the helpful reply. I had kind of thought the same about dryer life but I only got 9 years out of my GE junk that preceded this one so I was thinking that they just don't make them like they used to. Witness four thermistors and a handle so far.

Anyway, here's the info:
Model # 110.92822101
S/N: MM3615073

I'd done a quick parts check and the motor was about $140, give or take. On a service call I figured that'd get marked up a bit, plus at least 2 hours on the labor. That about right? Probably replace the drive belt as long as it's open - anything else? In major metro market so labor is high, figure I'm pushing $400.

My concern is always the control board going, especially after the thing is disassembled/reassembled.


 o
RE: Kenmore HE3 dryer motor - repair?

MM3615073 = 36th week of 2002 (it's sourced from Whirlpool; as you probably know, Kenmore is a brand label, products are sourced from other manufacturers).

I found an online source $110 for the motor.

It shouldn't take an experienced servicer more than an hr to do the job ... except for the stacked situation. Access is from the front, so there's possibility it doesn't need to be unstacked depending on the details ... in a recessed location, or clear to one or both sides.

What's your evidence for the motor being bad?

Other normal-wear items to check are the drum support rollers, belt idler, belt, and drum seals. No need to replace anything unless it's confirmed bad/worn.

Friend gave a 35-years-old Kenmore dryer to me a couple years ago (with a 10-years old washer, needed a $15 part) that they were going to toss out. Dryer was "slow," they suspected the element being weak/bad ... but elements typically either work or not, they don't normally weaken over time toward coldness, so I suspected some other problem. Ended up the top-mount filter had a broken handle so it wasn't pushed fully down (or cleaned very often). The unit was clogged with lint from airflow bypassing the filter. I cleaned it up, replaced the filter and rear drum seal that was aged, sold it for $80. The belt, rollers, & idler were in excellent condition, probably had been serviced at some point in time (the element had been previously replaced). Anyway, the point is that the 35-years-old unit had/has some years of good usage left.


 o
RE: Kenmore HE3 dryer motor - repair?

Update... Returned from the laundromat (ugh) this afternoon and while putting away supplies, out of sheer irritation I stood there pressing the start button for a good 10 seconds, maybe even longer, purely for the hell of it. Buzzing the entire time. And yep, it suddenly started turning. Opened the door, closed, pressed start and it cranked right up, not a buzz to be heard. Again, and yet again.

Clearly, there's still a problem brewing, but now that it seems that it's intermittent rather than completely dead, does that help with the diagnosis at all?


 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!


Return to the Laundry Room Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.


Learn more about in-text links on this page here