Return to the Laundry Room Forum | Post a Follow-Up

 o
Fisher&paykel GW612 beeping 1 sec intervals

Posted by Karsmi (My Page) on
Fri, Jun 21, 13 at 4:25

Hi Guys, my daughter has just watched a youtube video on how to make the washing machine sing the national anthem - she couldn't get it to work, But now when we turn the power on at the wall, all the lights come on and then we can start the cycle but after about 3 mins the machine starts beeping at 1 second intervals and the green light above the Short cycle and the one to the left of this one come on and also the red Spin light. The beeping and lights continue until it is turned back off at the wall. Clicking on the Wash level button also stops the beeping but leaves the lights on and you cannot change anything from then. Any ideas what the problem could be?


Follow-Up Postings:

 o
RE: Fisher&paykel GW612 beeping 1 sec intervals

Evidence thus far indicates a problem with the diverter valve -- beeping and fault code occurs ~3 mins into a cycle.

Trying running a load on Perm Press. The problem may not occur if the diverter is the fault, Perm Press cycle runs a different operational sequence that does not make use of the diverter and recirculation function.

Anything daughter did attempting to trigger the hidden music sequence shouldn't cause this problem ... it's coincidental that the problem occurred at that time. The diverter may indeed have gone bad.

Except ... if she happened to hit the right key sequence for changing the machine-size and set it wrong, but that still shouldn't affect the diverter directly.

612 is a 6.5kg/7.0kg machine. To check the machine size
- With power off, press/hold Wash Temp Up, then press Power at the same time.
- Should get 4 short beeps and the panel activates. Release the buttons.
- 6.5kg/7.0kg size is indicated by the Low water level light. 5.5kg is Cold temp light. 7.5kg/8.0kg size is Spin Hold light. If the size is wrong, set it right using the button under the respective light, then press Power to exit.

Playing music is via Demo Mode. This works on U.S. EcoSmart models, can't say for sure about NZ/Aus models (such as your GW612).
- With power off, press/hold Advance, then press Power at the same time. Release the buttons.
- Press/hold Wash Temp Up for a couple seconds to play a tune. Press/hold again for the next tune.
- Disconnect the mains power for about 15 seconds to reset out of Demo Mode.


 o
RE: Fisher&paykel GW612 beeping 1 sec intervals

Hi, can't believe I found this post trusty F&P is playing up after many years of reliable service. Following instructions it would seem I have 4 codes 14, 30, 75 and 1. This was only after using the spin speed buttons up which showed different sequence of lights each time I toggled up. Can you help?


 o
RE: Fisher&paykel GW612 beeping 1 sec intervals

Specific model number please ... or is your machine also a GW612?

There are 16 diagnostic levels, toggled via the spin speed buttons. Only level 3 (Hold and Slow lights on) is a fault code, the others are different info or settings.


 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!


Return to the Laundry Room Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Please review our Rules of Play before posting.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.


Learn more about in-text links on this page here