Return to the Garages/Workshops Forum | Post a Follow-Up

 o
Only 1 remote will prog. at a time CraftsmansOpener 139.53674SRT2

Posted by bobo_2006 (My Page) on
Mon, Aug 14, 06 at 21:09

I have just replaced the batteries on both on my security+ "Three-Function Remote Control Units" and I can't get both remotes programmed. When I go to program both remotes I can only get one programmed at a time. I erased all remote control codes as outlined in manual. Manual says to go back and program each remote control unit one at a time by:

Remote control unit "A"
1. Pressing and hold the selected remote control push button.
2. Then press and release the SRT (learn) button on the back panel of the opener. (All indicator lights work as outlined)
3. Release the remote control push button.

This process resulted in the correct programming and remote works.

Remote control unit "B":
When I go to program the second remote according to the same instructions it will not accept the program or work. The indicators lights don't operate as they should.

I went back and erased all codes and programmed the remote that wouldn't program "Remote B", and it allowed the programing and worked. When I tried to program "Remote A", (this is the one that worked during the first programming try), it wouldn't take the programming.

Can anyone help me with this problem?
Thanks, Bob


Follow-Up Postings:

 o
RE: Only 1 remote will prog. at a time CraftsmansOpener 139.53674

Bob, call this number 1-800-528-5236 and they will do their best to help you. It is the number for a technical service representative at the manufacturer. It will help if you have your model number handy and are near the opener when you call.


 o
RE: Only 1 remote will prog. at a time CraftsmansOpener 139.53674

Bob,
I own a lift-master security+ GDO that was installed in my home by the previous owners in 1998. Like you, I'm having exactly the same problem. Unfortunately, the person I spoke with at the 1-800 number for lift-master was not very helpful. I'm curious as to whether the technical folks for your GDO were able to solve this problem.

Thanks,
Chuck


 o
RE: Only 1 remote will prog. at a time CraftsmansOpener 139.53674

Update:
This problem turns out to be a defective remote. The gdo and the remotes use 'rolling' codes. If one of the remotes reverts to a "fixed code,' then this problem occurs. Purchase a new remote compatible with the gdo and program that first. Now try programming each of original remotes. Whichever one does not program is the defective remote.

Chuck


 o
RE: Only 1 remote will prog. at a time CraftsmansOpener 139.53674

Chuck;
This is the first chance I got to look at the postings. I have not called the service reps yet. You indicated that you were having the same problem. You mentioned that the gdo and the remotes use 'rolling' codes. If one of the remotes reverts to a "fixed code,' then this problem occurs. Did your orginal problem allow you to program either remote first and it worked then the second one (no matter what order the Remote A 'or' B was programmed first or second) would not take the code, as in my case. Could you elaborate on this?
Bob
,


 o
RE: Only 1 remote will prog. at a time CraftsmansOpener 139.53674

My problem was similar to others posted, except we have two GDOs (139.53681) for separate single doors, and when we moved in only one GDO would open by the remotes, the other would not open with any remote. Worse yet, the previous owners had that second unit locked and I found out why... when I unlocked the door at the corded unit I returned home later to discover the door was open! I think (at least I hope!) it was on the same code as a neighboring GDO...
Anyway, was able to use JayDee's method of quick press of the red button instead of the 6 second version indicated on the instructions (after fully resetting the unit to clear from access that other opener out there), and now I have both doors responding to their appropriate openers!
Thanks to JayDee and all of you for your posts... it took me a while to read through them all, and I took notes hoping one solution would work, and it did! -Raf5043


 o
RE: Only 1 remote will prog. at a time CraftsmansOpener 139.53674

Many apologies for the delay in sending this message. Have been out of town and only gotten back now.

Bob -- My problem was I could program the first remote "A" and it programmed. However, remote "B" would not program. If I cleared all codes on the gdo and programmed remote "B" first, it programmed, but remote "A" would not program. No matter what remote I programmed first, "A" or "B" it would program, but the second remote would never program.

The problem according to the technician was the 'rolling codes.' If the gdo is using 'rolling codes' and one of the remotes becomes defective and uses 'fixed coding' it will not program. His solution was to purchase new remotes and I am happy to report that his solution was correct. I purchased two new remotes. Both of these new remotes programmed. Of my two original remotes, one of them programmed, the other did not. The one that did not was the defective remote; i.e., the one that was using 'fixed coding.'

I hope this helps.

Chuck


 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!


Return to the Garages/Workshops Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Please review our Rules of Play before posting.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.


Learn more about in-text links on this page here