Return to the Renewable Energy Forum | Post a Follow-Up

? Type of Insulation to Use with Asbestos shingling

Posted by chipster_2007 (My Page) on
Sun, Jul 20, 08 at 20:21

I want to have my home insulated but do not know what type of insulation to use in the walls? If I use cellulose, will i be creating a potential problem due to the asbestos shingling that is on the outside? Some installers say they can double pak or maximize the amount of cellulose blown into the walls so that it will act as an air barrier. Is there any truth to this or are they full of hot air. Need to make my decision soon. What about cellulose in the attic vs. fiberglass batts. Which are better? Winter's just around the corner? Any help greatly appreciated. BTW, I live in MA and it gets pretty cold up here.

Follow-Up Postings:

RE: ? Type of Insulation to Use with Asbestos shingling

In the attic, I would go with cellulose. Loose fill FG under cold conditions develops convection currents within the insulation that can reduce its effective R value by half. See this ORNL test of loose fill cells and FG:

For doing walls, there is a practice with cellulose that most installers call dense packing. This is real and beneficial. They put the insulation in at a somewhat higher density which makes it fill better and eliminates any possibility of settling over time.
Cellulose does offer some resistance to air flow (more so that other loose fills, but not as much as foam in place), but not sure what the issue with asbestos siding would be?

Before adding more loose fill to the attic, you should seal up any penetrations from below (wires, plumbing, light fixtures, ...) -- this is a major heat loss on most homes.
And, if you have ducts running through the attic, seal all the joints with duct mastic, and insulate the ducts if they are not already. These things are a lot harder to do after you add a couple feet of loose fill :)

Great book on insulating: "Insulate and Weatherize", Harley.


Here is a link that might be useful: Loose fill insulation

RE: ? Type of Insulation to Use with Asbestos shingling

Asbestos siding can't be drilled to allow for the insulation to be blown into the wall cavities in the typical fashion such as wood siding or shingles. The shingles need to be carefully removed so that they are not damaged, cracked or broken.

An option might be to have the insulation installed from the inside through the drywall, especially if interior renovations are planned.

RE: ? Type of Insulation to Use with Asbestos shingling

Asbestos shingles are a big problem. Since no one can guarantee they won't break, I need to be prepared. Is there any particular way of removing them that would minimize the breakage? I am really hesitating to insulate given the liklihood that some will break. I know there are replacement shingles out there, fiber cement, but don't know where to get or how to paint to get color as close to what is there. Any suggestions appreciated.

 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!

Return to the Renewable Energy Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Please review our Rules of Play before posting.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.

Learn more about in-text links on this page here