Return to the Electronics Forum | Post a Follow-Up

 o
NiMH batteries & cordless phone

Posted by libbyliz (My Page) on
Sat, Jul 29, 06 at 23:51

I have a dual handset 2.4 GHz Uniden phone that takes two AA 1.2 volt 1500 mAh NiMH batteries.

The main phone batteries are bad & need replaced.

I've been to every friggin' store known to carry a wide selection of batteries & all they have are 1.2 volt 2000 & 2500 mAh NiMH.

I called Uniden & was told the only battery I should use is AA 1.2 volt 1400, 1500 or 1600 mAh NiMH otherwise the batteries may "burn up" the phone.

Three stores I've been to said the opposite; that I can use the 2000 or 2500, that such won't ruin the phone & that the 2000 & 2500 only pertains to the amount of charge they'll hold. The folks also said that if my phone uses a 1500, it just won't use all the charge of the 2000 or 2500.

So I looked at the Uniden website but the only AA batteries they sell have no information, such as if they're alkaline, NiMH, Niox, etc., nor what charge.

So I e-mailed them about this dilemma & won't hold my breath for a reply.

Who's right/wrong?

I don't want to have to buy a new phone just because I can't find the right batteries!

Nor do I want to ruin the phone I have by using the wrong batteries!


Follow-Up Postings:

 o
RE: NiMH batteries & cordless phone

In your situation, I would use any NiMH battery that had the proper voltage specification, fit into the cordless phone, and connected properly with the existing contacts. I would be concerned about the effects of a defective battery leaking and damaging the phone, but I would not be concerned about any adverse effect due to battery charge capacity, specified as mAh, or mill-Amp hours. I would expect a battery with fewer mAh to run down faster, and a battery with more mAh to last longer. This is not an issue if the phone is left on the charger when not in use. However, if cordless phones are routinely left "off the hook," so to speak, the battery will eventually run down.


 o
RE: NiMH batteries & cordless phone

if cordless phones are routinely left "off the hook," so to speak, the battery will eventually run down

This is exactly what happened to the main phone.

I thought the battery (didn't know it was two AA instead of a pack) was like the old batteries where the charge had to be completely depleted before recharging.


 o
screwed up quote

if cordless phones are routinely left "off the hook," so to speak, the battery will eventually run down

This is exactly what happened to the main phone.

I thought the battery (didn't know it was two AA instead of a pack) was like the old batteries where the charge had to be completely depleted before recharging.


 o
RE: NiMH batteries & cordless phone

Our SONY cordless phone, about 10 years old, uses a 3-cell NiCad(nickel-cadmium) battery pack. The phone is always on the charger/base station when not in use. We rarely if ever run down the battery. The charge rate is referred to as "trickle charging," a very low rate. It does not cause the battery to overheat, or become warm. Maybe the battery would last longer if the phone spent less time on the charger. Does your owner's manual give some specific recommendation regarding battery care and battery charging?


 o
RE: NiMH batteries & cordless phone

The manual actually says, now that I read it (DUH), to keep the phone on the charger when not in use. I was always leaving it off the charger.

Okay, now this is really weird... after I posted my dilemma, I decided to put the old batteries back in the phone to see if I could still use it for more than a couple seconds, maybe a minute here & there until I got new batteries. I left it on the charger before using it today, just in case.

I just ended an approximately hour-long phone call with my sister!!! And when I hung up it still showed a full charge!!!

So now I don't understand what was going wrong with it to begin with; why the phone would tell me there was no charge when not even a minute before I picked it up it was fully charged. ???


 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!


Return to the Electronics Forum

Instructions

  • You must be a registered member and logged in to post messages on our forums.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review the contents and make changes.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • It is illegal to post copyrighted material without the owner's consent.
  • HTML codes are allowed in the message field only.
  • No advertising is allowed in any of the forums.
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.



 
Click here to learn more about in-text links on this page.