Return to the Electronics Forum | Post a Follow-Up

 o
Testing TV antenna signal

Posted by davestexas (My Page) on
Mon, Mar 25, 13 at 21:51

Back in the CB days I bought a SWR meter so I could 'tune' my CB antenna. Can I use it to view signal strength for OTA TV signals?
When the OTA signals went digital, I installed an antenna in my attic so I could view local channels.....Off provider.
Much better HD reception on both audio and video than from provider!
Of the dozen or so local OTA stations, most all are on one tower about 15mi away and all 'look down' on my location.
Bougth a Tivo to record those signals and had a problem yesterday. The signal from the local Fox station kept pixelating and the recorded program was unwatchable....NASCAR race.
The Tivo has a signal-strength meter for all signals received and it kept going from 0 to 80+ on that one station only.
The day was VERY windy, but unless there was a problem at the tower, that shouldn't matter.....right?
My antenna is not amplified, so that could be a problem on that one station, or maybe going through the Tivo degraded the signal strength enough to cause the pixelating?
Anyway, I'm curious if my SWR meter is of any use with this problem?
Thanks


Follow-Up Postings:

 o
RE: Testing TV antenna signal

Sorry, but an SWR (standing wave ratio) meter will not help you here - it reads the transmission line reflections from a radio transmitter which you are transmitting on - has nothing to do with reception.

OTA digital signals are very prone to disturbances that may have only caused a little snow or ghosting on analog signals. A large tree swaying in the wind in a direct path of your antenna and the transmitter could cause a situation like you described.

Get an antenna "pre-amplifier" that mounts at the antenna - often a two piece amplifier and power injector system - not a "distribution" amplifier that is meant for feeding multiple locations. Then use the digital tuner signal strength meter to aim your antenna on the weakest station.


 o
RE: Testing TV antenna signal

Hi Bill. So the SWR meter isn't helpful and remains on the shelf. I have a SP-813 amplified antenna on the way that should do the job. I found the compass direction for the stations I receive. The one I had the trouble with was about 5° off so I reoriented it and that helped a little.
Thanks for your advice. I appreciate the help.


 o
RE: Testing TV antenna signal

Dave - hope the new antenna solves the problem. Please post a follow-up as to how it works for you - it's become a fairly problem common that lots of people have had to deal with.

What's really amazing though, is that the pixelation and breakup always occurs at the best part of the movie or football game!


 o
RE: Testing TV antenna signal

Or, NASCAR race!


 o
RE: Testing TV antenna signal

Follow up:

Since OP I bought an amplifier for the square-grid antenna I've had installed in my attic for years. It did help some.
Bought and installed a lava motorized antenna. It does ok, but having a motor on it is pretty-much useless, since the controller does not indicate where it's is pointing or what direction it is rotating. Basically it's a set-it/forget-it type.
I also bought an SP100 omni-directional antenna. It too does ok and found a few more channels. I do not have a signal strength meter but have one on the way. It, hopefully, will help tune the antenna better than me using only a compass.
I will try to mount the omni unit outside and out of sight to the HOA spys. It doesn't look like tv antennas once did. Looks more space-age.....frisbee with a 24" wing on each side 180° apart.. That installation will be the best I can do given where I live. That will involve a little more work (grounding the mast and grounding the cable-shield). I think my biggest problem with OTA signals has more to do with the 70' Red Oak tree in my front yard tho....


 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!


Return to the Electronics Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Please review our Rules of Play before posting.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.


Learn more about in-text links on this page here