Return to the Home Disasters Forum | Post a Follow-Up

How to kill mold between walls?

Posted by chuckr30 (My Page) on
Wed, Jan 31, 07 at 15:15

I am highly allergic to mold. I moved into a new house in 2004 which sits on a slab, no basement. Since then my asthmas has been acting up. I did a repair under my sink and noticed I seem to have black mold growing there. There are sections of my house which are open to the sand, the slab is missing in parts! Thus allowing moisture in and mold to grow.

How do I kill the mold and keep it away? While bleach will kill it it will not keep it away as chlorine is very volatile. I prefer a spray in a DIY form, so I can go up to the attic, and spray down each header into the wall between each stud (headers have many holes for various reasons).

Follow-Up Postings:

RE: How to kill mold between walls?

you say the slab is missing, is this just around plumbing or other items coming from under the slab? around here slab houses usually hav ethe plumbing and some electrical conduits run before the slab is poured. then they box in around the plumbing and pour the slab, leaving a small "hole" in the slab. if you look under the tubs in my house, there is slot about 2ftX1.5ft of missing slab where the water pipes and drain line come thru. no mold issues there.

are you sure you have not had leaks?

if you want to block moisture from coming in at those points, maybe fill each hole with spray foam. then treat and kill the current mold. if it is bad enough, or certain types of mold, your only recourse is removal of the affected areas. some types cannot be removed, as they easily spread elsewhere and the entire house must be abandoned.

i read about a couple that had this happen to their brand new multimillion dollar home. the contractor pierced a water line, and a slow drip caused so bad of mold the house was condemned and for health reason they could not even take the clothes on their back with them when they were forced out. hope yours is not that bad!

RE: How to kill mold between walls?

Thank you for your reply.

Yes, the slab is missing 1) under the kitchen sink, 2) under the wall between the kitchen and bathroom where some pipes go into the ground and 3) where the shower drain goes into the ground (in another closet). Under the kitchen sink is an old well head, it shows you they didn't have city water when the house was built, and I found the old septic tank too! (It's empty.) We now have city water and sewer.

House was built in 1954. Yes I did have the original drain pipe going from the kitchen sink to the main sewer rust through. Water collected under the kitchen sink. I had the pipe replaced (half of the bathroom slab had to be demolished then replaced), so that problem is fixed.

No, mold is not that bad, but when I look under the sink I can see the studs and black stuff all over them, which I assume is mold. The other part is I am very allergic to mold and my asthma is acting up since I have been in this house. Before I moved in I didn't need medicine. Now since I moved into this house I take medicine every day, except in the summer months.

Asthma problems only during cool months point to a probable mold problem.

Any suggestions for a spray that will keep killing mold once it is sprayed on?

RE: How to kill mold between walls?

I am allergic to mold too - every mold I've been tested for.

I have mold behind the paneling in my basement, but nothing that's out of control. I use a dehumidifier, which seems to help. As far as treating the mold, try a product called "Mold Avenger" - recommended by a reputable paint store that I go to on the other side of town. I was told this will help reduce the mold greatly, but will not rid it entirely or forever, but it is not harmful to your health and is effective for up to a year. You can help to prevent regrowth by removing the elements that are creating the mold. If it's moisture, reduce the humidity in your home with an air conditioner or dehumidifier or a combination of the two.

Good luck!

RE: How to kill mold between walls?

You need to open all the areas that you see mold on. Spraying only the exposed mold is useless. Dumping chlorine into walls is dangerous and not effective. Open the areas and have them treated professionally. Fill in all the missing areas with concrete over a vapor barrier.

 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!

Return to the Home Disasters Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Please review our Rules of Play before posting.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.

Learn more about in-text links on this page here