Just an update: It's here, sitting proudly just off my living room, which is not where I had hoped for it to go. Try as I did, it is just too deep (front to back) to fit in my bathroom where my old washer is. So it will go near my galley kitchen. There's still alot of work to do to get it up and running. I need to add a 120-240V/15A circuit breaker (or a fuse or easy-install kit for the existing 240V outlet) and run new wiring. A means of attaching it to the kitchen sink to drink from and drain to. A Y-adapter to feed cold water to both the cold and hot inlets. (I've relegated most of my installation issues to this thread). My dryer - an old, small GE ventless unit - is starting to become unreliable too. If I find a decent used condensation dryer at a good price I may get that too. But here I see I run into a problem - evidently Miele hasn't made 6kg ventless condenser dryers. They have lots of 5kg condensation dryers, but I don't think they can be stacked atop a 6kg washer like the W1926. Correct? I'm in the dark about whether some sort of stacking kit is needed to stack a Miele dryer atop a Miele washer, and whether only certain combinations of W & D can be stacked. It appears it is although I can't find any references to specific model numbers and the stacked machines shown in their manuals don't seem to list any particular additional hardware, Anyone here familiar with this? And is stacking a non-Miele condensation dryer on a Miele washer verboten? Is there some sort of homemade mount you can build that will keep the dryer from sliding off? If I had a closet, I'd just build a shelf a few inches above the washer and be set. I could reverse the old layout - washer near kitchen, dryer in bathroom. Then I could use any brand. I have a 120V/15A dryer now but can go to a 240V condensation dryer that should increase my options considerably. Miele and Bosch seem to sell for much more secondhand than Asko or other brands. I'm also seriously confused about the plugs, outlet, and wiring required by the W1926. It's rated at 120-240V/15A, yet is fitted with a Hubbell NEMA 14-20P plug, the type normally found on a grounded 125V/250V 20A (not 15A) device. The electrical cord is a Carol 12/4 Type SJ (UL) (also listed as CSA Type SJ FT-2), with a sticker noting that the black and red wires are the L1 and L2 hots respectively, with a white neutral and green ground. Why not 14-gauge cable ending in a usual 240V/15A plug as Bosch uses? Further confusing things, the Miele owner's manual seems to indicate the plug is a NEMA 14-30P, the big ones normally found on 240V/30A dryer plugs. Could this not be the original cable or plug? The new double-pole circuit breaker should clearly be 15A but should 14-3 w/ground or 12-3 w/ground NM-B (Romex) cable be run? (I lean towards the latter since that's what the washer cord uses). I may have been better off with one of the 5kg Miele washers - it would have fit in my bathroom and I could stack a Miele condensation dryer over it eventually and save space. They are essentially alike only 4 inches shallower front to back, and with (even) higher spin speeds. But I hope to someday have a larger home and then I can take the W1926 with me and use any ol' normal vented dryer, and I'll be glad I have the extra space. The Miele really is nicely designed - very straightforward controls that tell you what they're doing - no "workout wear" or "kid's clothes" settings that leave you wondering what it's really doing. And of course, actual temperature markings, a rarity in U.S.-market washers. Can you imagine an oven that didn't show temperatures, just "cold", "warm", and "hot"?

Hi my problem is choosing the correct compact washer. I'm trying to decide between purchasing an Asko 6424 washing machine versus a Miele 1623 because of their compact size and fit into the space for my washer - can't be more than 37.5 inches height, 29 3/4 inches width. The only issue is which one? I heard that the Asko comes with 220v which only works with the comparable Asko dryer - that if I only purchase the washer alone it won't work at all in Canada, where the voltage is only 120v or if you say it will work in Canada with its 220v, the other issue is it won't heat water to 100F without hook up to its mate dryer. Also, I was told by one retailer that Asko is recommended over Miele because Miele is hard to find parts for repair. I was also told that the Asko model is superior because it doesn't have a rubber seal inside the washer as opposed to Miele which does come with the standard rubber seal. I'm worried about the rubber seal inside the Miele causing this odour as I found that my current Bosch front loader has a rubber seal which does cause an odour when used. Last, capacity of the Miele is good coming in at 6K and I'm not sure what the capacity of the Asko is as it doesn't say what capacity on its website. The price for both washers come in at the same price $1699.00 but Miele is offering a 200 dollar discount this month which means the 5 year warranty will be free because that is the cost of a five year warranty or 200 dollars. So as far as price goes, I would find today a 200 dollar saving by purchasing the Miele over the Asko. But is this worth it if the Asko is a better machine? Any ideas which is the better washer. I am shipping to Canada BC Thanks

You hear good and bad about all brands. There's many happy LG owners posting on this forum. There's people who have had bad luck with all brands. That's called reality. A heater isn't truly mandatory in my opionion but I think it's a good idea as long as it works on enough cycles to be functional, and raises the temperature of the water, not just maintains the temperature. The Epics have gotten a lot of good reviews, and they should, they're Whirlpools and a proven design. Samsung does not build machines for them anymore - that's old information. I understand your budget concerns and I think you're looking at good models. I do like the suggestion of the Miele though. Now $2000 for the washer is a lot, but considering the amount of laundry you do, you can justify it. However, with any of them, I would suggest you consider NOT getting a matching dryer. Save the money there and put it toward the washer. A large (7.4+) CF Whirlpool dryer can be bought for about $400-$500 or less and they're excellent dryers. I bought mine for $300 and would buy it again in an instant. If you're going HE, and especially with a heater, you need to be prepared for long cycle times. 2-3 hours worth. It takes time to heat the water and the tumbling action needs more time to clean the clothes over an agitator. You sound sold on a FL so I won't suggest looking at the HE TLs. And I haven't found anyone who can give rational reasons for steam either in the washer or dryer. I think the word is "gimmick". If you have a laundry tub next to your washer, you can run the water in the tub to get the hot water close to the washer to have it warmer going into the tub. Keep in mind the tub itself will cool the water down. That's why a good heater could be valuable. But it's not the end all be all either. Advantage sometimes? Yes. Essential? No. People have washed and sanitized clothes for years without them. And as you're looking, get figures on water temperatures in degrees, not ambiguous terms like "hot", "warm" or "cold". What's hot to you may well be cold to me.

Since this thread was recently updated, thought I'd post my own updates. In my 2 earlier messages re my Hoover Twin tank, I mentioned that I loved it but the plastic was falling apart. Hoover did replace it in March of 2014, but by December the same problem was occurring. The blue plastic just seems to disintegrate. I've read other complaints about the same thing...it's quite astonishing to be pushing the mop along and having bits and pieces, and then screws just falling out along the floor. I plan to call Hoover tomorrow. Realistically, although it's still within the 2 year warranty, since they've already replaced it once I have no hopes of getting a replacement unit, nor am I sure I even want another one.