Is it at all possible you backed it up using the wrong suffix? Do you still have the original file on your hard drive. If you did give it the wrong suffix and you still have the original file on the hard drive simply burn it to the CD again with the correct suffix. If you deleted the original then copy the messed up file back to the hard drive and rename it with the correct suffix, then burn it again.

owbist, have done the deed, had 1 red error, rest are the blue internet Explorer icons on the left side. Here is what the red one said, and there are scads of these icons. Details Windows Operating system ID-54 Source-print Version 5.0 Component appl(can't read my own writing here) Symbolic name-message bad job Message doc %1was corrupted and has been deleted. The ass. drive is %2 Print job caused the print spooler to stop more than once, so the previous spooler deleted the job and won't try to pring again. The Internet icons have this in the event viewer WOS ID 7036 Source Service Control manager Version 5.2 Symbolic name event_service_status_success message the %1 servers entered the @2 state. Can you decifer what this all means? I don't have a single yellow error message, and only one red, which is the first one I wrote in this message. All the rest of the entries are IE icons for some reason or another. I didn't read them all, just the one listed for yesterday, they started in June I believe, and have continued since. I first encountered them when i went online some picasa forums, were foreign I believe, and are shared magazine patterns, and other things from all around the world. Do you think that might have something to do with this?

Sometimes new roads never get put on the maps. One time while working in Pensacola,Fla I got a service call and the dispatcher told me it was a small street off of 9 mile rd just east of K-mart. I drove up and down that section of road about three times and could not locate the side street I was looking for. Finally I stopped at a little store and called the customer to inform them I couldn't find their street. The asked where I was then she laughed and said, "sit tight, i'll be right with you." About 5 minutes later a lady walked up to my pickup and asked if I was the one looking for her street? I said yes and she says, "You see that house with the back of the house facing the parking lot here? Thats my house." Then she says, "You go ahead and drive over and I will grab a couple things here at the store and meet you in about 5 minutes". I pulled back out on the road and went about 100yds, then turned down a super long driveway which had an L shape at the end and her house faced the driveway. Thats odd I thought, but its no skin off my nose if ppl want there house to face the driveway. While working on her water heater the lady told me that the builder had originally intended to build a whole development there so they put the road way in and began selling lots. She and her husband had bought the first lot and had their house built but in the mean time the builder had went to prison so they never completed any more houses. Then she told me that when they originally laid out the development the roadway into the development had been deeded to the county as public thoroughfare for the project and in fact the only portion she actually owned was the short L section from her driveway to the long roadway. She said that she and her hubby had made an agreement with the post office to put there mailbox on 9mile road so the postman wouldn't have to pull in and turn around for just one house then she said the county had been trying for years to convince her and her hubby to take possession of the roadway as their driveway, but the had repeatedly refused. I asked why they would refuse and she says, simple, as long as its a county right of way the county has to pave it and maintain it ..LOL

I don't know about the error code, however, most newer dryers will specify a certain time for drying while in "dry sensor" mode. If the load is not at a specified moisture amount at that time, the machine will "hold" at that point until the moisture level reaches the pre determined point, then will progress omward into the cool-down stage. (usually last 7-10 minutes). This is not unusual, and is desired. I would assume the error code came about by you fiddling around. Have you tried to unplug for a half hour or so, and then restarted?