Return to the Cleaning Tips Forum | Post a Follow-Up

 o
bathroom help

Posted by knitforbrains (My Page) on
Sat, Sep 7, 13 at 20:46

Any advice on how to get rid of moldy-looking spots on the caulking in our shower/tub? I've scrubbed the heck out of it and tried everything from white vinegar to Tilex to straight-up bleach, but nothing seems to do the trick.

Also, our shower is a plastic insert and is starting to get that "ring-around-the-tub" look. It's starting to look really dingy.

Any advice to get things sparkling again? *I* know my tub & shower get cleaned regularly, but I absolutely hate the idea of house guests using our shower (only bathroom in the house) and thinking that it's unscrubbed or dirty. :S

Many thanks in advance ~


Follow-Up Postings:

 o
RE: bathroom help

People in here have tried Fantastic and say it doesn't work, but for me it melts the soap scum easily. I let it set until I see the dirty streaks running down. After reading in here I checked my shower and did see a dark shadow (I thought) about 4 inches high at the bottom of my shower insert and sure enough it was scum. It came right off. Now I make sure when I dry the shower I get that part. I don't even have to clean my shower because of drying it after my shower.

This post was edited by EmmaR on Mon, Sep 16, 13 at 16:09


 o
RE: bathroom help

Have you tried CLR? They make several products, one of which is a foamy spray type thing that comes in a bottle, specially for cleaning bathroom tile. I think it works partly because it actually sticks to the tile for a while rather than immediately running down the wall. Also, something like Softscrub (or my cheapie version of softscrub, which is 50% dish soap, Dawn is good, and 50% Borax) might do the trick as well although some elbow grease might be required as well as a good rinse afterwards).

I feel your pain - soap scum on the plastic is brutal. Once you get it off, a regular application of whatever you found that works for you is the only answer!


 o
RE: bathroom help

I think the trick is to let your cleaner do the work for you. I don't have too much success with the spray on bathroom cleaners. Organic is right about the Dawn, let it set a while and see if it melts off the soap scum. Wet a sponge, don't squeeze the sponge dry, apply the dish detergent to the sponge and walk away for a while. If the Dawn doesn't work, try a different dish detergent such as Palmolive. You just don't want to use anything abrasive (if fiberglass). Re: the moldy spots on the caulking, what you tried should have worked (if not remove the caulk, clean all traces of mold & recaulk with some of the waterproof caulking available (some have a 10 yr warranty).


 o
RE: bathroom help

It's surprisingly easy to give yourself a "new" shower. First, remove the caulking and replace it with mildew resistant silicone caulking.

Then, get one of the kits out now for painting even fiberglass showers. When I bought my house, the main bath had a gross dark green, filthy, cracked shower/tub. I took the hideous doors off, along with the track. I got the Rust-O-Leum kit for painting a fiberglass shower/tub. White. I followed the directions to a t. you scrub the wall with those green scratchy pads, get it as clean as you can and scratched up. Mix the two materials that come in the kit, and with a small foam roller brush, paint the shower. It's surprisingly easy, and the results are amazing. I rent my house in the summer to vacationers, and one of them this summer wrote a review for the Web site where I advertise the house, and in her review, she wrote, The bathrooms are new and sparkling. Nope, they're not. The white in the kit is SO bright. They work really well IF you follow the directions carefully.

For the full tub/shower combo, it took three kits. Total cost me $100. Not bad for a "brand new" shower and tub!

This post was edited by Tibbrix on Wed, Sep 18, 13 at 20:37


 o
RE: bathroom help

Dampen some paper towel strips or toilet paper and press it into place on the moldy area. Spray with a bleach solution till it's dripping wet -- press the paper to make sure it's making contact. Leave it till it dries.

If this doesn't work, I'm afraid you'll have to replace the grout. After removing it, do the paper-and-bleach treatment in the area before adding new caulk.


 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!


Return to the Cleaning Tips Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Please review our Rules of Play before posting.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.


Learn more about in-text links on this page here