Return to the Cars Forum | Post a Follow-Up

 o
Brake Drum out of Balance

Posted by jemdandy (My Page) on
Sat, May 15, 10 at 2:59

I've been driving since 1948 and this is the first time that I've ran into this problem. I had a high speed vibration that would begin above 60 mph and then get progressively worse quickly with more speed. The vehicle is a '98 Jeep Cherokee Limited, 6 cy, 4 sp automatic with 4 wheel drive. The 4 speed has both part time and full time modes.

This vibration problem began after work was done in two shops:
1. Tire leak fixed at Firestone and tires rotated.

Followed by:

2. At Car-X: Front wheel U-joint replaced with new design CV joints, rear drive shaft U-joint at the differential replaced, and rear brake shoes installed.

A couple of days later was the first time that I had the occasion to get up to expressway speed and then the problem was sensed.

I noticed that Firestone after the tire patch, had moved the red dot balance mark on the tire. Firestone corrected this and rebalanced. This helped a tiny amount, but the problem persisted. Rebalancing all the tires with wheels helped a bit, but did not solve the problem.

The tire rotation moved the fronts to the back and to opposite sides. This reversed the rotation of these tires. Since I had bought the vehicle (3 yrs ago) at 70,000 miles and it now has 85,000 miles, I had no idea of past maintence except I knew that the tires had been changed at least once because the ones on the vehicle were not factory issue and had too much tread to have been on the road for 70,000 miles. It was possible that the tires had never been rotated until I did it. I switched the left and right rear tires to switch the rotation direction ot see if that made a difference. It helped a little, but as I ran the vechicle the next week, the problem persisted. It was smooth up to 50 or 60 mph and then the vibration would set in.

At this point, this vehicle was speed restricted. It was ok for grocery shoppng and most of my errands, but could not be used for a trip of any length. Incidentially, the Jeep is my winter driver; I use a more fuel efficient vehicle for the remainder of the year. My policy for the fair weather machine is if there is salt on the street, it does no go out. This practice has preserved its finish and structure.

Neither Car-X or Firestone could not pin point the problem or solve it. And then I noticed that one of the brake drums did not have a balance weight. It is possible that it never had one if it was one of the rare ones that did not need one, but I have seen many drums with balance weights. Since this vehicle had been driven in winter road salt and the drum's outer surface was rusty, it was had to determine if a weight had been lost. There was a faint indication that it may have had one. The problem is that no one in town is equipped to balance brake drums and several techs scoffed at the idea this could be a problem.

In desperation, I put on a pair new drums. I reasoned this was not a total loss since the old drums were about 1/2 used up. Both of the new drums had balance weights and one was quite large.

The problem went away. It is vibration free up to 70 mph.

Has anyone encountered an out-of-balance brake drum?


Follow-Up Postings:

 o
RE: Brake Drum out of Balance

Sure, out of balance brake drums was a big deal with 70's and 80's GM cars. Thats why we had the ability to spin balance the wheels on the car. We were in fact correcting for the wheel and tire as well as the brake drum.

Anyway you fixed it the right way, new ones. If corrosion has gotten to the point that the balance weight came off, there is no way the drum was cooling correctly under braking.


 o
RE: Brake Drum out of Balance

Hi cherokee owners. Came here to share something and hope you understand posting in this thread that was posted months long. This is the second time i heard this. The first time was on my jeep. what i did was that i replaced the drum brakes. here are some of the procedure i knew.

First, Clean and lubricate anchor pin with hi-temp multi purpose grease. Then, clean and lubricate support plate shoe contact surfaces with hi-temp multi purpose grease. Next, Lubricate adjuster cable guides, adjuster screw and pivot, parking brake lever and lever pivot pin with hi-temp multi purpose grease. Attach parking brake lever to secondary brakeshoe with washer and new U-clip. Then, Remove wheel cylinder clamps. Secure shoes with new holddown springs, pins and retainers.

Installation:

# Install parking brake strut and spring.
# Install guide plate and adjuster cable on anchor pin.
# Install primary and secondary return springs.
# Install adjuster cable guide on secondary shoe.
# Lubricate and assemble adjuster screw

Useful link: Jeep Cherokee repair


 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!


Return to the Cars Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.


Learn more about in-text links on this page here