Return to the Building a Home Forum
| Post a Follow-Up
anyone use homehardware4less for emtek?
| | |
Posted by
michoumonster (
My Page) on
Mon, Feb 18, 13 at 17:04
| Hi all, I was looking through old threads on gardenweb and found a few references to this site called homehardware4less. Their emtek prices seem to be the lowest I have found. But the site itself seems very rudimentary. Was wondering if any of you have purchased from them recently and if you could share your experiences? Or if you could recommend another place with good prices on emtek hardware? thank you!! |
Follow-Up Postings:
RE: anyone use homehardware4less for emtek?
| | |
| We used them for our Emtek hardware in November 2011. I placed the order and two days later asked if I could add another lever to the order. (I wanted it added to the order rather than placing another order due to shipping charges.) The lever was added without a problem and the whole order was shipped together about a week later. |
RE: anyone use homehardware4less for emtek?
| | |
| thanks for your input dekeoboe! sounds like they are legitimate. I will give them a try. the savings for me will be close to 20%! |
RE: anyone use homehardware4less for emtek?
| | |
| Did you check Simpson Hardware? I read about them here and had a good experience ordering from them. I may be a good place to confirm your low prices. |
RE: anyone use homehardware4less for emtek?
| | |
| kfhl, thanks for the suggestion. i will price out at simpson as well. i was comparing the prices with build.com which claims to have the lowest emtek prices anywhere, but seems it is not the case... |
RE: anyone use homehardware4less for emtek?
| | |
Wondering if you had success with homehardware4less
Need to order my door knobs! :) |
RE: anyone use homehardware4less for emtek?
| | |
| I am ordering mine from Simpson. Their prices were the best. |
RE: anyone use homehardware4less for emtek?
| | |
| I am ordering mine from Simpson. Their prices were the best. |
RE: anyone use homehardware4less for emtek?
| | |
| Hi Laurat, I did end up ordering from homehardware4less. after price-checking with simpson, i did find they had the best prices for what I wanted from emtek. But I still haven't received my order, which was placed on 3/5. I got an email on 3/15 saying my knobs were backordered by the manufacturer. Then another email the same day saying that they would now be shipped within a few business days. It is now a full week later, and I still haven't gotten my order. Right now, I am a little on the fence about them due to delays and not many email updates. I suppose emtek is more to blame.. I will update this post to let you know once I get them, if all ends well. luckily i don't need my knobs immediately, but if you do, then it might be wise to look elsewhere.. |
RE: anyone use homehardware4less for emtek?
| | |
Hi everyone, I just wanted to update my post. I ordered a large number of emtek knobs and locks from homehardware4less. The only issue I had was a month-long backorder, but this was, according to homehardware4less, a manufacturer issue. My email inquiries received prompt replies from customer service. Now, I finally received my order. Everything was packaged well and my order came complete. The only thing I felt was lacking was a delay in communication about the backorder (took a good 10 days of silence before I learned of the backorder, then the knobs did not ship when they had said they would).
I saved a bundle by purchasing my emtek knobs here. I didn't need the knobs right away, so the delay did not hurt me (except worrying about not getting them for so long). But make sure if you do buy from these guys, allow for any potential delays. I would probably purchase from this vendor again if their prices continue to be better than others'.
hope my review helps any others wanting to buy emtek! |
Post a Follow-Up
Please Note: Only registered members are able to post messages to this forum. If you are a member, please log in.
If you aren't yet a member, join now!
Return to the Building a Home Forum
Instructions
- You must be a registered member and logged in to post messages on our forums.
- Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review the contents and make changes.
- After posting your message, you may need to refresh the forum page in order to see it.
- It is illegal to post copyrighted material without the owner's consent.
- HTML codes are allowed in the message field only.
- No advertising is allowed in any of the forums.
- If you would like to practice posting or uploading photos, please visit our Test forum.
- If you need assistance, please Contact Us and we will be happy to help.
