Hi i have been making hypertufa pots with weber grill,Just use a hammer and a chisel to pop the handles and legs off. I put about five layers of wet newspaper on the outside of the grill. and then about one half inch of tufa mix and then chicken wire ,Then about another inch of tufa mix . in 24 hours pop it out of the mold

I see you created two threads for this. I'll repost what I wrote in the other thread for continuity. ------ I have the Weber Performer. It's an awesome grill. I used a Weber kettle for years with great success, but in a moment of weakness I retired it for a Weber Genesis gas grill. Gas grilling is convenient, but it's not the same. Last year I purchased the Weber Performer to get the convenience of gas starting, but the cooking flavor/performance of charcoal. First, the propane assist is just a charcoal starter. I stack the charcoal in a compact pile over the starter and ignite it. Of course the bottom vents are wide open and the lid is off at this point. After about 3 or 4 minutes, I can hear the charcoal snapping, popping, and smoking to indicate it's "lit." I turn off the propane and let the charcoal burn down until nearly all sides are covered with fine layer of ash. Then, I knock the pile down and spread it evenly across the bottom grate for cooking. Now, I put the top grate and the lid on and open the top vent wide open. I watch the temperature climb to >400 degrees, then open the lid and brush the top grate to clean it. Close the lid and use the upper and lower vents to control the airflow and thus the temperature. After some experience, I know just about how much to close them down to hit a temperature range I'm after. This assumes you're using good quality charcoal and not using too much of it. I prefer the hardwood "lump" charcoal. The old standard Kingsford briquets don't seem as high quality as they once were. If, for instance, I'm cooking hamburgers, I'll have just enough charcoal to cover the bottom grate with the chunks spaced 1/2" to 1" apart. Hamburgers cook pretty quickly. Don't use the little half-round trays Weber includes to hold the charcoal for normal grilling. Those are for special circumstances when you want indirect heat. When I'm done cooking, I close all the upper and lower vent to extinguish the charcoal. I use the leftover charcoal from the previous grilling as the base of for the next cooking and add a little more from the bag to make the pile I want. One more tip, use the lower vent control lever in a back-and-forth motion BEFORE you begin to sweep the ashes into the built-in collection can. Clearing out any build up debris in the bottom of the kettle helps the airflow. Return the lower vent to full open position before lighting the new charcoal. If you aren't getting to the temperature you want, you may have crappy charcoal, inadequate airflow, or impatience. ------ After reading the additional information you posted in this thread, I'd want to reemphasize the need to mound the charcoal tightly on top of the propane igniter for the initial lighting and burn down. Turn the propane ALL THE WAY ON and leave it that way for the 3-5 mins it takes to light the charcoal well. It should sound like a weak torch with a touch of whistle to the outlet flame. Let the charcoal burn down in its mound before spreading it. Lid off and bottom vent fully open for the initial burn down. The propane igniter works great.

We went to a couple of barbeque places today and ending up buying the extra large Big Green Egg, and I think we will be very happy with it. Kevin thinks it will be great for parties, and now it will be even easier for us to cook for a crowd. Since we now have three charcoal grills, we can use separate grills for separate dishes which will make it easier for us to make multiple dishes at once, even if they require different temperatures. We also have the electric smoker, and I have to say that we get a more intense smoke flavor from that than we do from the charcoal - or at least it permeates the meat more. For smoking chilies, only the charcoal will do the job the way I want it. The BGE that we bought also has a pizza stone and can be used for grilling pizza - something that I've been wanting to do since first visiting the pizza making forum. We bought some outdoor lights for our pergola, and I think they will provide way more light than we required, but at least we can lower the wattage when we want to. I haven't bought anything for lighting the fountain yet because I want to have that installed by an electrician on an exterior wall of the house. I'm hoping to light much of the back yard that way and have it on a dimmer. I don't really want underwater lights in my fountain at this point but will talk with the electrician about that. I'm thinking that I will get my yard lit in stages and start off with getting some outdoor outlets installed at strategic points so that lights could be hooked up later. We went out for dinner this evening because I wanted sushi! We haven't assembled the Big Green Egg yet. Lars

We are in the process of building an outdoor kitchen and have decided to use a built-in 36 inch Lynx grill. As I was searching for the best price online I noticed that every seller had them at the exact same price. Is there a place to get Lynx grills below MSRP? Do they ever go on sale? Do they sell "open box" or demo items? If anybody has experience purchasing these grills at a lower than advertised price I would appreciate some feedback.