Return to the Bathrooms Forum | Post a Follow-Up

Shower Disaster, Need Help!

Posted by ms222 (My Page) on
Mon, Aug 19, 13 at 19:06

Hi, sorry for the long winded post, I'll make it as short as possible.

A little over a year ago I had my bathroom gutted and redone, overall it was an OKAY job. However, the shower curb is a total disaster, and I need some advice! (Not going to explain why, but the original installer will not help and is not an option to go to)

As you can see in this picture, I have a drop down shower, and my shower curb has a glass frame enclosure on it secured on the sides by drilling into the fragile glass.

My major problem is that the installer installed the shower curb horribly (he should have told me not to run the white tile floor perpendicular with the shower curb, but instead put a tile piece horizontal at the end so there would be no grout marks for water to get into.

But worse in the pictures you will see the blue glass tile extruding outward from the curb, and grout on the top and bottom of the glass tile. The problem is that these grout fills are about 1/2" and are cracking all over and do not hold up. I removed the grout from the top portion and filled it with silicone which has done the job for now (but you will notice in a picture before I did this water seeped through and cracked a tile! (plus now im sure there is mold under that tile).

Bottom line is I don't think the shower glass doors can be removed and put back in without ruining anything, so what is the most effective way to correct this issue the best I can, to prevent future water going under tiles and creating mold, as well as making it look better.

 photo 20130819_181227_zps84697258.jpg

 photo 20130819_181218_zps4d6f602c.jpg

 photo 20130819_181205_zps79b96b05.jpg

 photo 20130819_181149_zps4890119b.jpg

 photo 20130819_181138_zpsaa3649b2.jpg

 photo 20130819_181118_zpsa89921ab.jpg

 photo 20130819_181049_zps3189dd7f.jpg

 photo 20130819_181040_zpsd83f90b2.jpg

Follow-Up Postings:

RE: Shower Disaster, Need Help!

All changes in plane should be caulked, not grouted. Remove the grout with a hand held grout saw and replace with sanded caulk that matches your grout.

RE: Shower Disaster, Need Help!

Where the curb "bulges" into the shower...was that always like that?

If not, it's usually a sign that the curb was constructed with a wood core, that water has gotten into the curb, and now the wood is expanding due to being saturated with water.

The source of the water? It could be an improperly installed membrane at the curb. One where the installer draped the membrane over the curb, then fastened tile backer board to the curb by driving fasteners right through the top and sides of the curb, puncturing the membrane.

Or the membrane and tile over the curb could have been properly installed, but then someone drove fasteners through the membrane (example, the screws that secure the bottom hinge of the door).

Over time water can get through grout. If the membrane is punctured, that same water can wick into the wood core of the curb, cause it to expand, and blow out the tile and grout.

If it was just the grout cracking, then yes, I'd say the easy solution would be to remove the grout and replace it with caulk. But since the glass tiles have cracked and you have the visible bulge, that indicates movement. And movement usually indicates water intrusion and saturated and swelling wood within the curb.

With a saturated curb, I'll usually recommend investigating by removing tile from the outside vertical portion of the curb. That allows a curb inspection without touching the shower tile or the shower membrane.

With your shower being a sunken shower, without removing any of the glass all you could do is open the shower door and pop off the bathroom floor tiles that go right up to the edge of the curb. You need to see how the membrane is detailed.

Once you see the membrane, you can usually fold it back a bit to access the wood underneath. Excess moisture may be obvious, or you may need a pin moisture meter to measure.

The basic goal is to discover if the membrane was properly installed? If it was, how has it been compromised? If you find fault with that limited inspection, then you'd have to pull the glass and do the same to the remainder to that floor tile/curb intersection.

Then you repair and rebuild.

It won't be easy and it won't be fun. Compromised curbs are indeed the proverbial can of worms. Sometimes you can open it up, let it dry, make a simple repair, re-tile, and be done with it. Other times it leads to more and more digging and a full replacement of the shower pan.

RE: Shower Disaster, Need Help!

Hi guys, more information and pictures for you. The house is in Florida, built in the 1960's...the bathroom is built out with wood studs I think.

Address a few issues:

The blue glass tiles inside of the curb are not cracked or damaged. The only damage I believe is from the connection of the water getting behind the tile and the cracking of the tile. To be more specific, I am referring to the picture closeup of the white bathroom floor tile that right before the edge of the curb that cracked. I do not think this was from excessive force of me standing there or dropping anything. To be specific, this is how I think it happened. If you look at the interior of the curb you will see the top is the edge of the white bathroom floor tile, and in between the bathroom floor tile and the top of the interior blue glass tile, there is caulking I have in there to prevent water from getting in between the white bathroom floor tile edge and the top of the blue tile (the gap between the two). At first there was no caulking, just grout, which in a few months completely cracked and I did not notice it, so water was getting between the gap and under the bathroom floor tile. I think this water might have put upward pressure on the floor tile to make it crack, as the tile right next to it also looked like water got under it and made the grouting split. The crack in the bathroom floor tile when I touched it was moist, so I think it was from the water. Keep in mind the bathroom floor tile does not get splashed from the shower, as its on the otherside of the shower floor glass.

It is very possible that the bulge was there from day 1 and if I had to guess I would say it was..I just think it was a poor job. I do not know for sure, but it seems to me like the curb was built out of cement and not wood. I think he just laid the bathroom floor tile an inch or two past the cement curb frame, then put on thinset and laid the tile in the interior of the curb hoping that it would line up, but it clearly wasn't doing right. However, I have attached some pictures that may help a little bit, but maybe not so much.

I am tight in cash right now, so I do not think I can afford any signficant work on this issue right now, but I would like to know everyone's thoughts on how to take care of this the right way for the near future when I have better cash flow.

In the meantime, if I chip out all of the cracking grout from the bottom of the inside curb tile, and fill it in with silicone will I be okay for now and prevent any more damage/water damage (the top gap on the inside curb I already chipped out and siliconed a few months ago and is holding up)

RE: Shower Disaster, Need Help!

I might have misread your third photo. It looks like what I took to be a crack in the grout and tile might be a wayward strand of hair. lol

The thing to remember is that when you really pick things apart in proper shower construction is that caulk, tile, and grout are really not part of the true waterproofing system in a shower. They shed water. They make the shower look pretty to the eye.

The membrane beneath the tile is the actual waterproofing.

It certainly is possible that different methods were used in constructing your shower. If you are looking for a band-aid fix, then sure, recaulking can help by eliminating water penetration. Or if your shower is improperly constructed, or if the caulking is done wrong, it can hurt by sealing moisture in.

Cracked grout indicates movement within that grout joint. The reason the joint can have movement can be due to one of several things.

But for a band-aid fix, wherever you see cracked grout, remove the grout in that joint. If there is moisture behind the cracked grout, try to allow it to dry out. Then you can caulk.

 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!

Return to the Bathrooms Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Please review our Rules of Play before posting.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.

Learn more about in-text links on this page here