Return to the Bathrooms Forum | Post a Follow-Up

Replace the duct hose for bathroom exhaust fan, what kind to use?

Posted by Frizzle71 (My Page) on
Thu, Jun 13, 13 at 1:24

I am going to replace the exhaust fan in my bathroom (it is located in the side of the soffit that is above my tub, and was wondering what type of duct work is best to use to connect the fan to the opening in the wall to the outside?

Right now, there is about a 3-foot piece of ridged flexible hosing, that kind of resembles a vacuum hose, only 3" wide. It was actually disconnect from the fan when I looked inside. It must have worked it's way loose over the years.

I was wondering if this is the best type of hose to use? Or maybe a rigid type of smooth duct work would be better?

I took a quick look on the Home Depot website, and they don't seem to have any specific type of duct work or hosing for bathroom exhaust fans that I could find.

The do have some flexible hosing (some that are insulated too).

What would be best?


This post was edited by Frizzle71 on Thu, Jun 13, 13 at 1:26

Follow-Up Postings:

RE: Replace the duct hose for bathroom exhaust fan, what kind to

You can use a dryer hose and a clamp. After attaching the hose - use some duct tape to seal the connection.

If the entire run of hose is only 3' long - no sense in using an insulated duct.

If the old hose is in good shape, reuse it.

RE: Replace the duct hose for bathroom exhaust fan, what kind to

Rigid 4" ducting, insulated, and NOT terminating in the soffit or attic would be the correct way to do it..

RE: Replace the duct hose for bathroom exhaust fan, what kind to

Jumping in here. Live Wire Oak, why the rigid duct and not the flexible insulated kind that is found at Lowes and HD? I have to get ducting for my fan and was thinking of the insulated flexible kind. I would run it tight (without sags).


RE: Replace the duct hose for bathroom exhaust fan, what kind to

Smooth rigid is always best. Flexible duct creates way more resistance to air flow.

And, please, don't ever think about using flexible hose on a dryer. Lint catches on all the ridges and creates a fire hazard.

RE: Replace the duct hose for bathroom exhaust fan, what kind to

Catbuilder, Thanks for the information. I think I will use rigid then, in my exhaust fan situation. I have rigid for my dryer exhaust with the seams headed in the correct direction so lint has a harder time catching. No screws, only taped ends :)

RE: Replace the duct hose for bathroom exhaust fan, what kind to

Ridgid is really the only way to go especially over long runs.

We usually spec 4" sched. 20 PVC pipe as it comes in longer lengths than 4" metal does around here , though elbows can be tough to source sometimes.

Unfortunately most contractors / HVAC guys will use flexible corrugated hose because it's cheap and fast. If it's a luxury project they'll splurge for the flex aluminum instead of the plastic kind. This type of pipe can cut a fan' effectiveness in half over long runs. Little thought is really given to these fans in most homes today. They are often undersized for a given bathroom and poorly located too. The crappy pipe detailing makes a bad situation worse.

Panasonic's website has (or used to) a pretty good tutorial on how to properly size a fan, where to locate it and how to properly pipe it to the outside.

I think much of the problem is cost and ignorance. Most people know you get a fan in your bath , but when pressed they won't really be able to tell you its there to expel warm moist air from your home, not smells. They assume that the $34.95 version will be fine for them and a quick & dirty install will get ya out the door for a hundred bucks. The reality is, many master baths, and some hard working kids baths need a much larger fan than 35 bucks can buy. We are often talking $100-$200 for an adequate model, more if you want features or quietness. Add the increased piping cost and labor for the proper venting needed on higher capacity fans and this can quickly become a $500 line item - which starts to look crazy for something as pedestrian looking as a bath fan.

Timer switches are also a very good idea as most fans even properly sized ones need to run a while after you've left the bath to completely exhaust the moist air.

RE: Replace the duct hose for bathroom exhaust fan, what kind to

Thank you all for the information!

 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!

Return to the Bathrooms Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Please review our Rules of Play before posting.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.

Learn more about in-text links on this page here