Return to the Basements Forum | Post a Follow-Up

Framing a Basement

Posted by sdemjsully (My Page) on
Mon, Apr 1, 13 at 16:46

I'm about to begin framing out the basement, but had a general ceiling plate question. Probably a basic question, but can't find any good references online.

Most of our 9' basement ceiling is unobstructed, however, there are several places where the gas line (or other) hangs just below the joist. We're planning to drywall the ceiling, not install a suspended ceiling.

Anyway, question is this: should I attach 2x4s to the joists and THEN attach the ceiling plate? Thinking that I can't drywall right on the joists, as I have the above-mentioned issues.




Follow-Up Postings:

RE: Framing a Basement

First off, I would strongly recommend not using drywall on the ceiling of your basement, especially if it cover any mechanicals than might need service later. If a water line ever spring a leak the odds are about 100 to 1 against the water following a straight line down. You'll end up ripping up the ceiling looking for the leak. It also become a nightmare if you ever want to run new electrical, gas, water, phone, TV, ethernet, etc.

One way to deal with mechanicals is to box out around them. Depending on your situation it might be easier to move the gas or water line between the joists.

RE: Framing a Basement

@Mike: we were thinking of doing drywall, since we really don't like the look of suspended ceilings and the rest of our house is drywall; nor have we had any of the issues you mentioned.

Plan was to build soffits around the mechanicals.

With the way the gas and AC lines are currently situated, I can't move them between the joists without going through a major, end-to-end project. Electrical lines are fed through drilled holes, but the gas lines are not...they're bracketed to the bottom of the joists every 8 feet or so.

Assuming we did go with drywall, would the best course of action for attaching the ceiling plate be to attach 2x4s to the joists before putting up ceiling plates, or is there another, more effective method?

RE: Framing a Basement

Why put up drywall or plaster anywhere services run in a house? After all, it will be more difficult if they need to be accessed. It's because looks do count. (Unless it's a loft where utility is the look.)

You don't need two by fours, only shimming enough to allow the drywall to clear the pipes and hangers. Two by twos or one by twos. Or, as pointed out above, box around the intrusions.

One hint: use foam insulating sleeves on any water supply pipes to prevent them sweating in warm weather.

Also, take some pics before you drywall in case you need to access anything later. You might also want to include an access hatch, even if it's just to peek in case of problems down the road.

This post was edited by worthy on Mon, Apr 1, 13 at 22:48

RE: Framing a Basement

@worthy: thanks for the tips, especially the shims. That will save some dough.

The plans I've drawn up do contain a few access panels where we have water valves and other potentially important points of access.

I'm going to build soffits/boxes around the obstructions, but wanted a less involved solution for the entire joist area...hence the shims. Would have been so much easier had the guys that installed the gas lines when the house was built 8 yrs ago pushed them through drilled holes in the joists like the electrical lines...unless by code they can't.

RE: Framing a Basement

gas lines come in up to 21 foot sections, kind of hard to line up all the holes perfectly.

RE: Framing a Basement

Some areas, including this local area, permit the use of copper for gas lines. Nails and crews can puncture the copper.

 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!

Return to the Basements Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Please review our Rules of Play before posting.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.

Learn more about in-text links on this page here