Return to the Appliances Forum | Post a Follow-Up

 o
Maytag Dishwasher Repair??

Posted by chas045 (My Page) on
Wed, Jul 17, 13 at 12:03

I realize that this forum is mostly about appliance choice, but in the past I have seen that there a couple of people who were familiar with appliance repair. I am hoping they could point me in the right direction. I am generally handy and well equipped.

I have a poorly cleaning ~6 year old Maytag Quiet Series 300 Dishwasher. The first problem was that while dishes appeared clean, deep cups retained little dots of crud that could be easily removed by hand afterwards (not stuck on). That suggested a failure of the backwash filter that this unit claims to have. I have removed the large disk fine filter below the bottom sprayer and it has been completely clean. More recently, some dishes failed to clean at all and then I had to remove everything down to and including the little ~3 inch diameter, ~1/2 inch thick disk impeller because of a small piece of trapped broken glass that made a big racket. I have also found that my bottom spray arm has become somewhat worn and the threaded plastic cap that holds it on was really damaged so it didn't hold that sprayer exactly horizontal. I am working on a jury rig fix for this. However this spray arm does rotate during operation.

However, my larger problem appears to be that neither the top or middle spray arms appear to rotate. They almost always remain in the same location after 30 seconds of operation. Water does get up to these sprayers. When I open the door, water is still pouring down and I can see water still gently rising from the middle spray arm. My assumption is that the pumping action is not sufficient, but I am wondering if I don't understand the system completely. Is the 3 inch disk impeller the only pump, or is there something else to check out? This impeller seems kind of small for the job but I can't imagine where else water could be picked up from. The impeller is not damaged and it fits well on its shaft so I don't think it can slip.

Upper arm water is delivered from a manifold surrounding the impeller that rises at the center of the back wall and curves to the center of the top of the washer to a small spray arm. The middle arm picks water up from a tube that slides into the manifold thru a flex rubber flapper (there are actually two flaps; one is unused and remains mostly sealed). I worry about this connection because some water can easily slip by this fitting. However, there is an additional open hole in this manifold where a far greater water loss could be. This oblong ~1/3 inch by ~1.5 inch hole which points to the side of the washer does appear to have the capability to be connected to some non-existant (in parts breakdown) fitting. I have mostly closed this hole off with a piece of plastic hose hoping to raise the water pressure in the manifold.

I have seen references on line to some seal that is supposed to improve things, but I don't see how this would help and it appeared that the replacement would take a repairman a significant time and expense. Does anyone have any experience with my issues?


Follow-Up Postings:

 o
RE: Maytag Dishwasher Repair??

You need to cite the full correct model number from the machine's tag. Maytag Quiet Series 300 is a marketing name, not a formal model number.

Depending on design of the pump (if it has a so-called food chopper), there may be a screen associated with the chopper assembly that is clotted with debris (stray paper labels, fibrous food residue, seeds, pits, or bone fragments) which is obstructing water flow.

Some units have a slit in the upper manifold to spray a stream of water toward the upper rack for purpose of flushing debris off the bottom of cups and such. This probably is not the case for four unit since it apparently has a 3rd spray arm at the top. If the manifold is suspect of being cracked or damaged, consider replacing it.


 o
RE: Maytag Dishwasher Repair??

Thanks for the quick response. It is model MDB5601AWW.

It does have the little chopper thingie and the little screen. It was a little junked up the first time I looked at it several weeks ago, but not really clogged. I then took it off again when I had the broken glass issue and there was almost nothing in it and obviously nothing there now. BTW our well water is good and there is no build up of any kind. My small town independant appliance dealer who sold this unit and has a couple of repairmen and many spare parts was surprised at how clean the lower spray arm was. He didn't have the mounting cap! His repairmen are hard to reach and I don't want to call them if I can't come up with a explanation for possible repair. I occasionally clean out the spray arms if I find bits of crud especially in the holes that create rotation. Everything is clear with no paper crud on the plastic bearing surfaces.

The manifold is not cracked in any way. The oblong hole is obviously part of the design and there are mounting supports for something to snap over it. However the something is not shown in the exploded view and as far as I know was not on the new unit. I suppose it could in fact be a place for an unneeded slit sprayer. It would be at the correct height.


 o Post a Follow-Up

Please Note: Only registered members are able to post messages to this forum.

    If you are a member, please log in.

    If you aren't yet a member, join now!


Return to the Appliances Forum

Information about Posting

  • You must be logged in to post a message. Once you are logged in, a posting window will appear at the bottom of the messages. If you are not a member, please register for an account.
  • Posting is a two-step process. Once you have composed your message, you will be taken to the preview page. You will then have a chance to review your post, make changes and upload photos.
  • After posting your message, you may need to refresh the forum page in order to see it.
  • Before posting copyrighted material, please read about Copyright and Fair Use.
  • We have a strict no-advertising policy!
  • If you would like to practice posting or uploading photos, please visit our Test forum.
  • If you need assistance, please Contact Us and we will be happy to help.


Learn more about in-text links on this page here