fluorescent tube

ionized_gwJanuary 9, 2010

I have an 18" tube in the kitchen that won't budge from the fixture. I tried putting on a rubber glove for traction, to no effect. Should I break it and pull the end caps out. Any other suggestions?

Thank you for reporting this comment. Undo
kudzu9

Are you rotating the tube so that the pins align with the slotted opening? Get someone to help you with this, because breaking the tube is a bad idea: it can send shards of glass flying at great velocity in all directions.

    Bookmark   January 9, 2010 at 4:54PM
Thank you for reporting this comment. Undo
ionized_gw

I won't turn. I will take precautions if I break it. I plan to wrap it in something before breaking it if I go that route.

    Bookmark   January 9, 2010 at 4:58PM
Thank you for reporting this comment. Undo
pharkus

Y'know the weird part? I haven't read this thread until just now, yet I was daydreaming about stuck fluorescent tubes yesterday! (yes, I think about stupid things when I'm bored).

My elected solution was exactly as you propose: to wrap the tube with something, then break it in the center and pull the ends out.

I've seen three totally different types of fluorescent lamp connectors. One has a round path with a slit through the center of it, another is more of a Y-shaped opening with a slit at the base, the third is two distinct openings (one for each pin). I've had frequent problems with the circle ones where one side doesn't "let go of" the pin - you have to push up equally on one side while pulling down on the other. The "Y" type never has that problem, by design.

In any case, once you've got the lamp out (by breakage, if necessary) it'll probably be ridiculously obvious how to get it to cooperate next time.

    Bookmark   January 10, 2010 at 2:02AM
Thank you for reporting this comment. Undo
joed

There is also the type that is a pin. One of the tombstones on the end is spring loaded.
Post a picture.

    Bookmark   January 10, 2010 at 1:46PM
Thank you for reporting this comment. Undo
ionized_gw

Thanks, the light in question is the circular type tombstones. I broke the tube to remove it. I had trouble with another that is the "two openings" type. I put on my safety glasses and pried on the metal end caps to get that one out without breaking it.

I may have all three types, among about a dozen, under the cabinets in this kitchen. I messed with them for quite a while to get them all going swapping bulbs and starters. Maybe I should have pulled them all out and replaced them with something with electronic ballasts.

I may have figured out why the tubes are sticking. I discovered a box of 18" tubes in the detached garage and the pins look to be a little pitted from corrosion. Maybe some in the kitchen came from that box and suffer this same malady. This is a humid environment. I gave the pins a little rub with steel wool and put a tiny bit of dielectric grease on them.

The single pin picture reminds me that I have some 8Â T12s in the garage. One is intermittent. Any recommendations for fixing it? I have enough lights in there to keep the interior temp at about 50 F despite outdoor temps in the 20s/30s (night/day) for four days. It is fully-insulated, but there are a lot of light leaks.

    Bookmark   January 11, 2010 at 7:25PM
Sign Up to comment
More Discussions
ceiling fan, fan works but lights do not
I have 2 kids and one threw a toy that hit one of the...
katy_bug
Looking for Ideas For Lighting at base of 300' long driveway
Sorry for the "picture through the screen"...
dixieman
Replacing dimmer switch: different wire colors on new switch
My DR lights, which are controlled from two switches,...
msa6
Help with 240V 50A location
I'm trying to do a challenging kitchen layout. I will...
12crumbles
A/C wired to main panel only?
I had 2 electricians come out to bid upgrading my service...
frank_diy
© 2015 Houzz Inc. Houzz® The new way to design your home™