Craftsman Garage Door Opener- cant program Keyless Entry

pchamounDecember 12, 2006

I have a fairly new ( 1.5 years old) Craftsman 1/2 HP Garage Door Opener ( model 130.53910). I have bought 3 Keyless Entry systems ( Security + with rolling code technology) as it says in the garage Door opener manual, followed the directions line by line and I could not get the Keyless entry to program? What could be the issue??

Thank you for reporting this comment. Undo
doorguy06

What is the model number on the keylesses you are buying. Security plus means rolling code technology and there are now two of them out there that operate on different frequencies and are not interchangeable. If your learn button is purple you need a 53754 sears keyless if it is red you need a 53684 model number.

Don, GDS, Sdello

Is there somewhere I can go to learn all these sears model numbers. I only know Liftmaster and the sears keyless model numbers by heart.

Thank you

    Bookmark   December 12, 2006 at 8:16PM
Thank you for reporting this comment. Undo
Don_

doorguy06 as far as I know there is no cross reference for Sears. I sure wish there was.

    Bookmark   December 13, 2006 at 5:11PM
Thank you for reporting this comment. Undo
pchamoun

hi doorguy

I have keyless entry model 53754, and I just checked and my learner button is red. I will go out tonight and get model 53684 and see if that works. Thanks

    Bookmark   December 14, 2006 at 11:20AM
Thank you for reporting this comment. Undo
jrhoudek

i have an older model craftsman 139.53677SRT garage door opener. i need to re-program my keyless entry. the owners manual directions all include a 'enter' button or another button, but my keypad only has the numerals 1-0 and has no ENTER or any other button. how can i re-program this keypad?

    Bookmark   June 17, 2008 at 6:52PM
Thank you for reporting this comment. Undo
don_1_2006

Does your keypad have wires going to the wall control?

    Bookmark   June 17, 2008 at 7:03PM
Thank you for reporting this comment. Undo
jrhoudek

yes it does have wires going tothe wall control

    Bookmark   June 17, 2008 at 8:28PM
Thank you for reporting this comment. Undo
don_1_2006

To program the keypad, first unplug the garage door opener from the electrical outlet. Next, remove the nameplate from the console that the keypad plugs into and locate the program/operate switch. Flip the switch to program. Next, enter your desired four-digit PIN number into the keypad. Slide the switch back to operate and plug the garage door opener back in. The keypad should be programmed.

    Bookmark   June 19, 2008 at 5:59PM
Thank you for reporting this comment. Undo
keith_howell_bell_net

recently installed a new opener one of the remotes worked other did not, may have tried my old remote,would that be the problem if so how can it be rectified

    Bookmark   April 20, 2011 at 10:30AM
Thank you for reporting this comment. Undo
don_1_2006

An old remote could sure be your problem. You need to eliminate it and then program your new remotes. Without model numbers though I am flying blind.

    Bookmark   April 20, 2011 at 4:45PM
Sign Up to comment
More Discussions
Door knob
My front door knob screws won't stay tight so if I...
padfoot4768
What is this stove part called
Found this item in the oven, I know it came from the...
pegasus101
Where to purchase Spanish roof tiles? I just need 2 pieces.
One handyman came to my house to evaluate the price...
janesylvia
how did gap between floor and wall close up by itself?
I have hardwood floors and there is/was a spot at the...
tlbean2004
Removing mold from joint compound container
I have a container of Sheetrock All Purpose Joint Compound...
africanboy
People viewed this after searching for:
© 2015 Houzz Inc. Houzz® The new way to design your home™