Need help on stippling

FireFightersMoMOctober 29, 2008

I have been quilting now for a couple of years. I love the look of stippling on quilts.

But I can't seem to get it right. I am getting better with my speed every time. But here is my problem. The back looks terrible. I am embarrassed by it. I work so hard on all of it, and then mess it up in the back. Of course it is way to hard to take it all out.

I use a darning foot, I lower my feed dog. I tried to mess around with the thread tension and didn't notice a difference. I thought it was just something that would get better with experience, but it is not at all.

What am I doing wrong? I am total self taught. I can't find it idea's in the books I have

Thank you for reporting this comment. Undo
solstice98

When you say the back looks terrible, do you mean it's loose and you can see the thread from the front of the quilt coming through? If that's the case, you do need to increase the tension I think. You also should try moving the fabric more slowly under the needle. Keep up the machine speed but take your time with the motions. Does that make sense?

Kate

    Bookmark   October 29, 2008 at 10:00PM
Thank you for reporting this comment. Undo
mary_c_gw

You seem to be doing all the right things, which leads me to think it is a tension problem.

Do you have loops or loose threads on the bottom? If so, you need to tighten the bobbin thread.

Many will say, clutching their hair and bosoms, Never adjust your bobbin tension! The world will end! Well, yeah, not so much. Different threads need different settings. I adjust both bobbin and top thread frequently.

I set the top thread tension at about the middle of the range. Then I adjust the bobbin tension to match. Make small adjustments - less than a quarter turn of the screw. This is of course using the same thread top and bottom. Then if I change threads, it's usually just the top tension that needs to be changed, and usually by just a point or two.

You need to make up a few trial quilt sandwiches and try, try, try, all sorts of adjustments. Little and often is the key.;

    Bookmark   October 29, 2008 at 10:17PM
Thank you for reporting this comment. Undo
redpenny

I agree with Mary C it is a bobbin tension problem! I also adjust both bobbin and top thread. I also use the same thread I use on top in my bobbin......I just have better luck I also only use cotton thread....also like
Kate said ....Keep up the machine speed but take your time with the motions.
Also just like Mary said You need to make up a few trial quilt sandwiches and try, try, try, all sorts of adjustments. I always do that and what type of batting are you using? I like to use cotton batting when I decide I am going to either meader or do stippling....
Red

    Bookmark   October 29, 2008 at 11:55PM
Thank you for reporting this comment. Undo
faytay

Are you pulling your bobbin thread up to the top? I think that helps eliminate the glob of threads on the bottom. You make one stitch and then pull on the end of the top thread until the bobbin thread loops on the top and then you pull it up. Can't hurt to try.

Faye

    Bookmark   October 30, 2008 at 3:57AM
Thank you for reporting this comment. Undo
damascusannie

Often when stippling you will have to tighten the TOP tension till it's quite tight. Experiment by tightening the top tension almost as tight at you can, stipple a bit, loosen 1/4 turn, stipple a bit--keep doing this until you get a good, balanced stitch.

Annie

    Bookmark   October 30, 2008 at 8:11PM
Sign Up to comment
More Discussions
Old/new names
So I (we) don't lose anyone, I think listing our forum...
jennifer_in_va
Spider Web
And I still have lots of scraps!!! The first border...
nannykins
2015 February Block Lotto
(posting this a bit early so you can get a head start...
toolgranny
Another feature found
So, I found another feature that I thought you a) might...
jennifer_in_va
What should I do with these?
I picked up this jelly roll of Kaffe Fassett fabrics...
Fran Sajewicz
© 2015 Houzz Inc. Houzz® The new way to design your home™