Shaw sink owners, what flange and garbage disposal do you have?

amberleyMarch 26, 2010

Long story short- it seems like my 1 HP Waste King 3-bolt batch feed may not work with the Rohl extended flange I purchased. If you have a Shaw sink, which flange and garbage disposal did you choose?

I definitely want a batch feed, and I would prefer 1 HP, but I would settle for 3/4 if I had to. Any suggestions?

Thank you for reporting this comment. Undo
altagirl

Sorry, I have a 3/4 HP Insinkerator continuous feed with the Rohl extended flange and an air switch. Did you check the Rohl website to see if you can have a batch feed disposal with the extended flange? It seems like the disposal is too far down to get the cover in to lock in place.

    Bookmark   March 27, 2010 at 9:10AM
Thank you for reporting this comment. Undo
amberley

altagirl- forgive me if I am being dense, but I am not following you. What do you mean by the disposal being too far down?

    Bookmark   March 27, 2010 at 10:10AM
Thank you for reporting this comment. Undo
amberley

bump -hoping more people see this :)

    Bookmark   March 27, 2010 at 4:51PM
Thank you for reporting this comment. Undo
amberley

bump

    Bookmark   March 27, 2010 at 9:24PM
Thank you for reporting this comment. Undo
niffy

I have the insinkerator cover control evolution with an extended flange. Unfortunately, the extended flange Fergusons sold me (some other brand that I ASKED them to double check would work with the batch feed!) doesn't work with the cover control, so we await the correct Insinkerator version! Meanwhile, we can touch the magnetic top to a part under the sink, at the disposal, to get it to work.... The Insinkerator manual does come with instructions about which parts are necessary to use with fireclay and extra thick sinks. Amazingly quiet disposal!!

    Bookmark   March 27, 2010 at 10:49PM
Thank you for reporting this comment. Undo
mythreesonsnc

Amberley,

Sorry I can't offer guidance --- but I have the same specs planned (3/4 or 1 hp wasteking batch feed with a Shaw's sink). I haven't placed any orders yet, but would love to learn the correct set-up as well before ordering! Thanks for posting!

    Bookmark   March 28, 2010 at 8:45AM
Thank you for reporting this comment. Undo
amberley

mythreesonsnc- don't buy it yet until I have this figured out next week. It is a possible that the specs on Rohl's site are wrong. I spoke with them at length about this and they are basically saying that they never tested the 3-bolt Waste King with it, but assumed that since it was a 3-bolt it would work. They didn't exactly say this- but they are trying to cover their #@$.

niffy- the ISE cover control is the black one right? Which flange did Ferguson's sell you? And which flange are you getting now? I checked ISE site, and they say that you can't use a batch feed with their extended flange.

I am going nuts on this!

    Bookmark   March 28, 2010 at 9:33AM
Thank you for reporting this comment. Undo
altagirl

amberley - Sorry I didn't check in again yesterday so didn't see your question. I guess I was thinking that with a batch feed disposal the cover has to come into contact with the disposal and lock in place to turn on. My disposal is pretty low from the bottom of the sink with the extended flange. I probably don't really know what I'm talking so I hope I didn't make matters more confusing for you.

Good luck with resolving this!
Maria

    Bookmark   March 28, 2010 at 10:19AM
Thank you for reporting this comment. Undo
amberley

bump -hoping more Shaw owners see this!

    Bookmark   March 28, 2010 at 5:13PM
Thank you for reporting this comment. Undo
donho

I have a 30in Shaw's sink and the InSinkErator Evolution Cover ControlT. I bought the chrome extended flange from Insinkerator. No issues with installation.

    Bookmark   March 28, 2010 at 5:35PM
Thank you for reporting this comment. Undo
amberley

donho- THANK YOU. So at least I know that I can install a batch feed with a Shaw sink. You said you have a chrome extended flange from ISE? I can't find one made buy them in chrome. I have the Rohl flange in chrome, which should fit an ISE, which is what it looks like I am going to have to get.

How do you like this disposer itself? How long have you had it?

    Bookmark   March 28, 2010 at 5:45PM
Thank you for reporting this comment. Undo
amberley

bump.

Does ANYONE out there have a Waste King batch feed with a Shaw's and Rohl extended flange???

    Bookmark   March 29, 2010 at 8:53AM
Thank you for reporting this comment. Undo
donho

amberley -

the insinkerator is very quiet, so much quieter than my last unit which was not all that old. i've been using a couple of weeks only, but i like it so far.

    Bookmark   March 29, 2010 at 10:12AM
Thank you for reporting this comment. Undo
amberley

donho- do you have a CHROME extended flange from ISE? I could not find a chrome one. Where did you get it?

Thanks!

    Bookmark   March 29, 2010 at 10:32AM
Thank you for reporting this comment. Undo
amberley

HELP!! This stupid thing still won't work!! Where can I get a chrome ISE extended flange??

    Bookmark   March 30, 2010 at 11:23AM
Thank you for reporting this comment. Undo
Andy_B

In order to use a Waste King disposal with a Rohl Shaw's sink (or any sink thicker than 3/4" for that matter) you will need to use an ISE flange and an adapter. I just installed mine after trying many different flanges, and finally found this solution:

Parts you will need:

1. Extended ISE compatible flange (part #FLG-SSLG)
2. Waste King 3-Bolt Mount Adapter (part #3101)
3. ISE Quick Lock Mounting Flange (part #QLM-00)
4. ISE body flange (part #5298)
5. EZ-Mount Waste King disposal (I used the Waste King L-8000)

I ordered all of these parts on amazon.

Installation:
1. install the ISE Quick Lock Mounting Flange per the package instructions, except substitute the ISE extended flange.

2. Next assemble the adapter portion -- in order from top to bottom: splash guard (from 3-bolt adapter kit), ISE body flange, adapter (from 3-bolt adapter kit), mount ring (included with disposal). I found it helped to smear a small amount of dish soap between the splash guard and mount ring or else there was too much friction between the two. Press this whole assembly onto the flange installed in step 1 and twist the mount ring to lock into place.

3. Garbage disposal will now twist into place on the mount ring.

See my assembled disposal below:

    Bookmark   August 23, 2013 at 3:11PM
Sign Up to comment
More Discussions
Two toned kitchen love em or hate em?
I am loosing my mind. I originally wanted a dark shaker...
abick2
Those tall coil spring type faucets: Hard to clean?
Like this: http://ak1.ostkcdn.com/images/products/6382868/Residential-Coil-Spring-Brushed-Nickel-Faucet-f8de8fec-40cb-4993-a19b-7903391cc178_600.jpg (How...
raenjapan
Zephyr Monsoon I or Air King LIN34 600 CFR Range Hood Insert??
I am ready to buy a range hood insert for my kitchen....
Kenneth House
Kitchen Plan... getting closer!
I wasn't pleased with the idea of having to separate...
Dietitian
Crack in Quartz countertop
I purchased my Quartz countertop 7 months ago and I...
avsheth2002
People viewed this after searching for:
© 2015 Houzz Inc. Houzz® The new way to design your home™