How to determine Amps on an Arc Welder

Salkeld_FarmsAugust 28, 2005

Title says it all, well mostly.

I have a Arc 180 from Harbor Freight that I picked up for free. I downloaded the instruction manual from the site and have run a few sticks on it and it works fine. Only problem is that it was dropped (my guess is a couple times from looking at the case) and the actual variable gauge you use to determine amperage is all jacked up and doesn't really work.

So, my question is, without harming myself in the process, is there a way to use a multimeter to determine the actual dialed amperage?

Thanks - Craig

Thank you for reporting this comment. Undo
Pooh Bear

I have the Arc 110 welder.
Looks like it uses the same guage for showing the setting.
Looks like it just like one of the old radio indicators.
Should be easy to take it apart and fix it if it don't work.
If the sticker is gone showing the settings
just take a marker and draw them back on using the chart.

Pooh Bear

Here is a link that might be useful: Arc 180

    Bookmark   August 29, 2005 at 1:00PM
Thank you for reporting this comment. Undo
gooseberry_guy

Craig,

I'd just do some practice welds with it. Once you get a good weld on say, 1/4 inch stock, mark that as 125 amps and work from there. That will be approximate. Do the same for 1/8 inch steel. That will be about 90-100 amps. If the heat is too light, it won't penetrate and it will be hard to hold an arc. If it's too hot, it will undercut and burn your work.

My mig welder has three rocker switches and a wire feed speed control. No amps indicated, I just set them where I get good welds and remember those settings.

Another point with a stick welder, you need more amps with bigger rod, so keep that in mind. If you use a 1/8 rod on 1/4 inch stock, and it welds good, you will need to increase heat a bit with a 3/16 rod.

GG

    Bookmark   August 29, 2005 at 11:26PM
Thank you for reporting this comment. Undo
mla2ofus

Gooseberry is right. The amp selectors on most stick welders are just to get in the area of amps desired. After that a lot of variables come into play, such as rod dia,rod type(6011,6013,7018),thickness of metal being welded,position(flat,horiz,vertical,or overhead), and how close you hold the arc between rod and metal. It just takes experience to determine where to set the amps.
Hope this helps,
Mike

    Bookmark   September 20, 2005 at 8:05AM
Thank you for reporting this comment. Undo
john_in_ma

Measure the output voltage at the various settings and calculate your way backwards.

    Bookmark   September 29, 2005 at 9:26PM
Sign Up to comment
More Discussions
Metal/Iron Stair rail
I moved into a house last year. It is a tri-level home....
harmony5002
metal compatibility
I have a built in gutter on my gable roof. The gutter...
dustynight
Help - Cast Aluminum furniture cracks (Pic)
Hi, (Cross posted originally on decor forum and posting...
homey_bird
Horseshoes
I have an abundance of used steel Montana horseshoes...
lilbritches1
copper roof - caulked seams instead of solder???
We recently installed a small copper roof over a porch...
alice462
Sponsored Products
Copper Shade Floor Lamp by Tom Dixon
$750.00 | Lumens
Serena & Lily Cut Circle Sheet Set
Serena & Lily
Bolla Satin Nickel Three-Light Bath Fixture with Ceylon Glass
$499.50 | Bellacor
Smart Decorative LED Arc Desk Lamp Pink
ParrotUncle
Arteriors Home - Mara Large Pendant - 41002
Great Furniture Deal
Lite Source Cadee Chrome 3-Light LED Arc Floor Lamp
Lamps Plus
Worthy Leather Corner Sectional (3 piece) - Brighton Zinc Beige
Joybird Furniture
Steelcase | Move Stool in Color
YLiving.com
© 2015 Houzz Inc. Houzz® The new way to design your home™