ecosmart GWL15 Problem

leonel_2010July 29, 2010

Machine stop at the end of the spin cycle so light 1 and 7 are on with a beeping sound.

Thank you for reporting this comment. Undo
dadoes

Fault Code 130, Single Rotor Position Sensor Error - the motor controller board found an error in the data pattern received from the Rotor Position Sensor.

The Rotor Position Sensor (RPS) is a component inside the motor used to read its rotational position so the controller board can operate the motor for agitation and spin. Possible causes of this error are a bad wiring connection (broken wire or corroded connector) between the RPS and controller board, a bad RPS module, or (less likely) a bad controller board.

However, you should to check in Diagnostic Mode to confirm the fault code.

- With the machine's power off, press and hold Wash Temp Down, then press Power at the same time. Should get two beeps and the panel turns on. Release the buttons.

- Press Spin Speed Up and/or Down repeatedly as needed to get BOTH the HOLD and SLOW spin lights on.

- The last recorded fault is displayed on the eight wash progress lights in binary fashion. Add together the numeric value of the lights to get the code.
From left to right: 128, 64, 32, 16, 8, 4, 2, 1. For example, first light (128) + seventh light (2) = 130.

- Press Power to exit diagnostics.

Access to the RPS is from beneath the machine and requires disassembly of the motor. Specific steps & precautions are involved. I could send a service manual, but you don't have an e-mail contact on your GardenWeb profile.

    Bookmark   July 29, 2010 at 3:53PM
Thank you for reporting this comment. Undo
leonel_2010

ok Dadoes i did the diagnostics and these are the results:
press wash temp down and power at the same time , I got the 2 beeping.
press spin speed up and down: i did tit several time trying to get Both lights to come on the HOLD AND SLOW but not luck, when i press the spin up i get this code:
light # 8 red, , light 7 & 6 orange and light 5 green.error code = 15
Press the spin down i get this code: light # 7 & 6 solid orange,
so hope this info can help you.

    Bookmark   August 6, 2010 at 6:15PM
Thank you for reporting this comment. Undo
dadoes

Are you pressing Spin Up and Down at the same time? That's not how to do it, sorry if I wasn't clear.

There are sixteen levels of diagnostic readings, Level 0 through Level 15. Diagnostic Mode starts at Level 0. The spin speed lights indicate the level in binary. Add up the speed lights for the level you're in. Fast = 8
Medium = 4
Slow = 2
Hold = 1Press Spin Speed Up to move upward through the levels:Â 0 -> 1 -> 2 -> 3 -> 4 -> 5 and so forth.
Spin Spin Down moves back:Â 5 -> 4 -> 3 -> 2 -> 1 -> 0

You want Level 3 (Hold 1 + Slow 2 = 3) to get the last fault code, so immediately after getting into Diagnostics, press Spin Speed Up three times, then check the cycle lights for the code. If you go too far and pass Level 3, then you would use Spin Speed Down to go back.              Level 0 (no speed lights)
[spin up] -> Level 1 (Hold)
[spin up] -> Level 2 (Slow)
[spin up] -> Level 3 (Hold & Slow)

    Bookmark   August 6, 2010 at 8:22PM
Sign Up to comment
More Discussions
Stacking washer and dryers of different makes
I just learned that my Kenmore washer was beyond repair...
deleomeyer
The perfect appliance? (survey)
Hi everyone! Whether for kitchen, laundry appliances...
hainnovation
Undercounter washer and dryer
I want an front-loading washer and dryer that I can...
sooky
Eco Nuts Laundry Detergent
Has anyone here used these before. Saw them on Shark...
brentb21
Dark color spots on clothes after washing/drying
I have been having having this issue for months now...
tylerr27
People viewed this after searching for:
© 2015 Houzz Inc. Houzz® The new way to design your home™