is it ok to feel air where the cased coil meets furnace?

cindywhitallOctober 3, 2012

I doubt this is "ok" My unit is a cased coil that sits on top of what I call the "furnace". The supply duct comes out the top of the coil. I feel air blowing in about a 3-4 inch section where the coil meets the furnace and at the top of the coil where it meets the ductwork. It may be from the coil panel itself at the top, I can't tell for sure. I had pointed out the air leaking around the bottom of the coil when they came on day 2 of the install. They responded that they weren't finished yet and I said "ok". They did apply some silver caulk stuff (mastic?) in the area of the leaks and I didn't really check it again until today. On that first day I hadn't noticed it at the top, just on both sides of the bottom.

I want to know how unacceptable this is before I complain....don't want to be a serial complainer but....

btw, I made this a separate thread in case some knowledgable folks aren't following my other thread. This one should be pretty cut and dry. THANKS!

Thank you for reporting this comment. Undo

"don't want to be a serial complainer but.... "

Too late!

Some amount of leakage is not that bad, I would think. That's what duct tape was invented for.

    Bookmark   October 3, 2012 at 3:14PM
Thank you for reporting this comment. Undo

The bottom of the coil where it sits on top of the furnace should be sealed with a silicon caulk. The connection at the top of coil to the duct work should be sealed with duct mastic.

This should be fixed if the leakage is signicant. It is not so terrible since your furnace is in the basement.

    Bookmark   October 3, 2012 at 4:06PM
Thank you for reporting this comment. Undo

I'd use mastic tape. don't think I've ever
used duct tape on hvac jobs.
hardcast brand 1402 mastic tape is an
excellent product. seals to many different
surfaces as long as they are clean & dry.

all equipment junctions & equipment to plenums should
be mastic sealed.

best of luck.

    Bookmark   October 3, 2012 at 8:31PM
Thank you for reporting this comment. Undo

A small amount of supply air leakage through gaps between coil/furnace is not an issue at all. Of course it should be sealed as best as possible.

    Bookmark   October 3, 2012 at 11:52PM
Thank you for reporting this comment. Undo

Consider how much your existing supply air ducts are already leaking and I'm betting the small amount of leakage where the coil meets the furnace is minimal, relatively speaking. There is a lot of pressure that close to the blower. I prefer to seal it with paint-on mastic. The caulk (silicon?) they used on your system (shown in pictures on another thread) should be fine also if applied properly.

    Bookmark   October 4, 2012 at 12:02AM
Thank you for reporting this comment. Undo

They are coming Tuesday. My guess is they will use the same caulk stuff. It is leaking in 2 places and I don't think they are small leaks as they air seems to hit my entire palm when I hold it a few inches way, and in close.It's not like it's a 1/2 gap. It's in the basement, so it seems like a waste to let it leak there when I read so much on here about seal seal seal and seal some more! I was frustrated when I noticed it because I didn't want to have them have to come back out, and quite frankly, it SHOULD HAVE BEEN DONE RIGHT the first time! I thought I hired one of the best companies:(

    Bookmark   October 4, 2012 at 5:13PM
Sign Up to comment
More Discussions
1 vs. 2 stage cooling? 80% vs. 95% furnace?
I'm in SoCal near L.A. (zip 91354). Two story house...
M. A.
Advice on Attic insulation
So we just finished the second year in our house and...
Thoughts on proposed HVAC system?
To start: my house is two-level (main plus upper)...
Blown in insulation vs spray foam
I am looking for advice. I have a home built in 2000...
Has anyone found solution to HVAV Dirty Sock Syndrome
Two years ago I had a Trane heat pump installed in...
Sponsored Products
Rosalia Antique Bronze Nine-Light 23-Inch Chandelier with Royal Cut Clear Crysta
Area Rug: Simply Geometric Sand/Beige 2' 3" x 3' 9"
$83.00 | Home Depot
Sonneman High Line 9 1/2" High Satin Nickel Wall Sconce
Euro Style Lighting
Prichard modern sectional sofa
Interior Define
Larry Pendant by George Kovacs
$120.00 | Lumens
Le Klint | Le Klint Swirl 1 Pendant Light
$750.00 | YLighting
52" Kichler Rivetta Oil-Brushed Bronze Ceiling Fan
Lamps Plus
Easy Street Chaise Lounge in White
$999.99 | Dot & Bo
People viewed this after searching for:
© 2015 Houzz Inc. Houzz® The new way to design your home™