Down to 2 Estimates...

tomdxAugust 17, 2012

I need to replace a 24 year Rheem system in a 1300 sqf, 2 story Townhouse that I rent out.

I'm down to the following estimates....

TRANE ($5,900)

XL80 2-Stage (TUD2B060A9362A)

XB13 2.5 ton Condenser (4TTB3030E1000A)

XB series Coil (4FXCB036AC3CAA)

2-Stage Themostat

10 year parts/Life time Heat Exchanger/1 year labor

Lennox ($6,100)

SL280V (70,000 BTU) (single stage non-vs is about $300 cheaper)

14 ACX, 2.5 Ton 14 Seer

Coil (I was just told it would be matching)

Honeywell FOCUS Pro 6000

5 inch Media filter

10 year parts/20 year Heat Exchanger/5 year labor

Option to extend the Labor to 10 years for $400

My current furnace is 75k and A/C is 2.5 ton... no idea on the SEER

Lennox Rep told me that the 70k furnace was the correct choice because the next lowest is to low for my townhouse.

The Lennox A/C is 14 SEER (Up from the Trane's 13 SEER) because that qualifies for a Utility Co rebate, which makes the 14 SEER cheaper than the 13 SEER... which is fine by me as long as there are no drawbacks. I do have a concern that the A/C is rated at 76db... seems loud to me.

The Lennox Thermostat quoted is a single stage, but I know enough now that I would request a 2-stage if I chose the above furnace.

The Lennox Contractor is used by Costco for installs, been in Business 50 years, is rated A+ by BBB, and has excellent reviews on Angie's List.

The Trane Contractor is used by Home Depot for installs, been in Business 30 years, is rated A+ by BBB, and has excellent reviews on Angie's List. My concern here is that originally they also quoted me a Rheems system. When I told them that's the one I wanted, they came back and said the furnace was discontinued... I called Rheem to inquire, and they said it is currently in production with no intention to stop. Could be an honest mistake, but it does raise a credibility concern for me.

I have to make a decision by tomorrow so that the install can be done next week. I'd really appreciate any comments on Trane vs Lennox, this specific Lennox configuration, and on Lennox in general... I'm really confused.

Thanks

Tom

Thank you for reporting this comment. Undo
mike_home

I believe the XB13 is a builder grade (low end) condenser. You should get a quote on a better model. You need to get the model number of the coil otherwise you may get a third party coil. Insist on the manufacturer's coil.

For some reason Lennox gets negative comments on this forum. I have no experience with Lennox so I can't comment.

    Bookmark   August 17, 2012 at 9:12AM
Thank you for reporting this comment. Undo
tigerdunes

The XB series is much better than the Lennox ACX series.

On the Trane, I would prefer the XR13, on the Lennox, the XC13 model.

TD

    Bookmark   August 17, 2012 at 9:59AM
Sign Up to comment
More Discussions
Need help choosing an efficient HRV Air Exchanger
Hi, My house as a total area of 2300 square feet (1150*x)....
Jim_Lafleur
Noisy Compressor in Geothermal Heat Pump
I have installed a Cliamtemaster Tranquility 27 3 hp...
macleodaj
HVAC question
I live near Charlotte NC and have a new Bryant Hybrid...
gtodd1966
Enery efficiency of exposed ductwork?
What are your thoughts on the energy efficiency of...
ccintx
Navian condensing combi, good or bad?
Hi, I am looking into converting from oil to gas and...
rickyk22
People viewed this after searching for:
© 2015 Houzz Inc. Houzz® The new way to design your home™