Programming Garage Door Remote - Craftsman 1/2 HP

jwstell42December 1, 2007

Sorry to post yet another message about the craftsman 1/2 HP garage doors, but I have searched through the many posts and while some of the suggestions helped me some, I still can't solve my problem.

I have 2 Craftsman 1/2 HP Model number 139.53515SR garage door openers (They came with the house I recently purchased).

Through the help of this forum, I have been able to program the remote to the 1 garage door opener, but I cannot for the life of me get the second garage door opener to work with that remote, or a second one, of the same model number, which I purchased.

I have tried holding in the "learn" button, sometimes for as long as a full minute to attempt to reset it. Then pushed it once, and held the button on the remote, to no avail.

Is there something else I can do to try and get the opener to work? I'd really hate to replace the opener, it works just fine with the hard wired button on the wall, so the motor and everything else is fine. I just can't get it to work with the remote.

Thanks in advance for your help!

Thank you for reporting this comment. Undo
don_1_2006

If you can't get the opener to program using your known good remote then your logic board is bad.

    Bookmark   December 1, 2007 at 5:57PM
Thank you for reporting this comment. Undo
jwstell42

Ok, me being a novice to this sort of stuff - how do I replace / fix the logic board?

Thanks in advance for your help!

    Bookmark   December 3, 2007 at 11:09PM
Thank you for reporting this comment. Undo
don_1_2006

You are not going to be able to repair the logic board. It is replace only. It is the end of your opener where all those white wire go. If you had a new one in your hands you would know what was involved. They cost around $80.00.

    Bookmark   December 4, 2007 at 12:50PM
Thank you for reporting this comment. Undo
jwstell42

Ok thanks for the help, I guess I'll give that a shot.

    Bookmark   December 4, 2007 at 7:50PM
Thank you for reporting this comment. Undo
eddiew

I too have been having programming problems. I am trying to program the control built into my car. I tried using the learn button. Didn't work. My note about the Premium Control Console says it "Can be used to program the opener to accept additional remotes." It doesn't say how. Does anyone know? Thanks, Eddie

    Bookmark   February 5, 2008 at 3:55PM
Thank you for reporting this comment. Undo
sjtulirui_yahoo_com_cn

if it is a fixed-code model which uses dip switches to set the address pins of encoder and decoder ic, maybe you should check out the remote control dip switch calculator at solidremote, it will save you a lot of calculations.

Here is a link that might be useful: remote control dip switch calculator

    Bookmark   April 3, 2011 at 7:13AM
Sign Up to comment
More Discussions
Good material to patch potholes in old garage floor?
I have some pot holes in my 1963 garage floor. The...
griz8312
Craftsman Garage door openers old dipswitch technology
My garage door motors still work great- 30 years old....
mamasalvo
GDO / SENSOR LITES? ONE GREEN - OTHER ?
craftsman 1/2 hp battery key pad ok / remotes &...
bronxbill
Seeking advice on faux wood garage doors
Hello, X-posting in home building forum. I'd like to...
Madeline616
Shop vacuum
Are there any good 12 -15 amp shop vacs that have 1200-1500...
randalls1
Sponsored Products
Real Carriage 6-in. Skyrise Flush Pull - P-RC-SKYRISE06-S
$58.00 | Hayneedle
Home Decorators Collection Blinds & Shades Cut-to-Width Golden Oak 2 in. Faux
Home Decorators Collection
National Public Seating Combination Caddy in Brown
Beyond Stores
Slim Line Infratech 42.5 Single Element 2400 Watt Quartz Heater - AEIC100
$599.00 | Hayneedle
Quick Ship & Assembled Cabinets: Home Decorators Collection Garage Cabinets
Home Decorators Collection
SensaSwitch by Legrand
$34.98 | Lumens
Stainless Steel Under-the-Counter Paper Towel Holder
$5.99 | zulily
Merrimack Collection 12 1/4� High Outdoor Wall Light
$71.90 | Lamps Plus
People viewed this after searching for:
© 2015 Houzz Inc. Houzz® The new way to design your home™