Craftsman Garage Opener

weykoolMay 24, 2010

I just moved into a house with a single garage door opener, Craftsman, 1/2 HP, Model 139.539.60SRT. In the past month the garage door has opened "on it's own" 3 or 4 times. I attempted to reprogram the remote and followed the instructions on the opener. All lights "appear" to be functioning as stated, however, now the remote will not operate the opener. The door will open and close properly with the button on the wall, but nothing with the remote. When the remote is pushed the green light on the opener itself is flashing so the signal is there which tells me it's not the battery. Please HELP!

Thanks,

Gary

Thank you for reporting this comment. Undo
don_1_2006

Try programming the thing this way. Hold the button down on the remote and then press and immediately release the smart/learn button. If this doesn't work the logic board has quit working. You might pull it out of the opener and check it for loose connections.

    Bookmark   May 24, 2010 at 4:25PM
Thank you for reporting this comment. Undo
weykool

Don;
Thanks! That seems to have done the trick. Any ideas why it would have been opening on it's own? Perhaps a similar opener on the same frequency nearby? I am not sure if the previous owner has an opener and that was why I was attempting to re-program mine.
Again, THANK YOU SO MUCH!
Gary

    Bookmark   May 24, 2010 at 4:36PM
Thank you for reporting this comment. Undo
don_1_2006

Here are some things you can check.

Look at the LED light next to the SMART/LEARN button on rear of the motor unit. You may need to remove a light lens cover in order to see it. If the light is flashing rapidly this means you have a stuck button on one of your remote controls. Take the batteries out of each remote control. When you remove the batteries from the bad remote, the light will stop flashing. This remote needs to be replaced.

If one of your neighbors remote controls is inadvertently programmed into your receiver, you door will open when their remote is activated. If this happens you will need to clear out your receiver and reprogram your remote controls. Press and hold the smart/learn button for 6 seconds or until you see the small LED light near the button turn itself off. If the above steps have been followed and the symptoms continue, there may be an electronic short in either the wall control button or the receiver logic board. In this case, remove the wall control wires from terminals 1 and 2 on the motor unit. Should the symptoms persist after the wires are removed, replace the receiver logic board. If the symptoms stop with the wall control wires removed from the motor unit, replace the wall control button, and the wires leading to the wall control button.

    Bookmark   May 25, 2010 at 9:43AM
Sign Up to comment
More Discussions
2x6 strength? How much weight will a truss in my garage hold?
I want to build an engine hoist in my garage. I found...
work.truck
What's the Lowdown on Garage Door Brands??
I have read some prior posts on steel garage door brands...
Xena99
Craftsman garage door opener problems
I am having trouble with my 3 year old Craftsman garage...
magilla_53
who makes a 10x8 "Carriage House" style garage door?
Perusing the websites of most of the major garage door...
Daniel501
Chamberlain Garage Door Opener receiver problem
For the past 5 years, my Chamberlain Whisper Drive...
clarence_locke
Sponsored Products
Geneva HiFi Sound System XS Bluetooth - Geneva Lab
$249.00 | HORNE
Cambridge White Paint Shaker Kitchen Cabinet Sample
CliqStudios Cabinets
Melannco Black 6 OPG Collage
Overstock.com
Chrome Modern Heated Towel Rack Radiator Rail 47.25 x 23.5 & Valves
Hudson Reed
Side Table in Black
$259.00 | LexMod
Athena Outdoor Sofa with Cushions, Patio Furniture
FRONTGATE
People viewed this after searching for:
© 2015 Houzz Inc. Houzz® The new way to design your home™