Craftsman Garage door keypad...

balaApril 10, 2006

I have a 10 year old craftsmand garage door. Till last week, I am able to use the keypad mounted outside the wall. But now, the keypad does not work. The good thing is, still my remote and inside monuted pad works. I can see the lights on the outside keypad when I start pressing the buttons. Even I changed the batteries. I don't know whether the number got changed accidently or something wrong with the keypad.

Since I last the instructions to change the PIN on the keypad, I appericiate if anyone suggest me how to reset it, It is a wired keypad, NOT a wireless.

Thanks

Thank you for reporting this comment. Undo
Don_

To program the keypad, first unplug the garage door opener from the electrical outlet. Next, remove the nameplate from the console that the keypad plugs into and locate the program/operate switch. Flip the switch to program. Next, enter your desired four-digit PIN number into the keypad. Slide the switch back to operate and plug the garage door opener back in. The keypad should be programmed.

    Bookmark   April 10, 2006 at 5:47PM
Thank you for reporting this comment. Undo
bala

When I was trying your suggestion, I found that my keypad is a wireless one. Here is the model no.
Model: 139.53876.
FCC ID: HBW1162
Canada: K741

I searched your website for this model no and I found one result. whatever you mentioned for that request did not work for me. Do you think that I have to get a new wireless keypad?.

    Bookmark   April 10, 2006 at 8:20PM
Thank you for reporting this comment. Undo
Don_

Not sure what you found so lets start over. On the rear of your motor unit near where all those white wires go you will find a button. Press and immediately release this and then walk over to your keypad and key in your PIN. If this doesnt work and you replaced the battery with a good one you need a new keypad.

    Bookmark   April 11, 2006 at 1:00PM
Thank you for reporting this comment. Undo
bala

Hi Don,
I tried your suggestion. I could not succeed. Here is the more information.
On the garage motor, the model says: 139.53645SRT1 and the serial no is. 16562c01418 and the mfr 04/96. In the back of the keypad the model no shows that 139.53876

I bought a new wireless keypad of Chamberlain model which says it is compatible for the one I had. that also does not work.
I followed the instructions as it said.
1. I pressed the green button on the back of the garage motor. The green light came up and stayed for 30 seconds.
2. Within that 30 seconds, I entered a 4 digit code on the keypad and hold the enter key for about a minute.
I did not see any blinking or the clicks of the garage door light.
As per the instructions, it is supposed to acknowledge the new code by signaling the clicks on the light.

Can you help me what could have gone wrong and how to figure it out?.
Thanks

    Bookmark   April 12, 2006 at 9:23PM
Thank you for reporting this comment. Undo
skdino_comcast_net

My wireless garage door opener keypad keeps draining my batteries, I put a new battery in and it only last for about one week, any help.

    Bookmark   May 26, 2011 at 7:38PM
Thank you for reporting this comment. Undo
bcarlson78248

If this is a rolling code door opener that has one large square button and two smaller round buttons - Craftsman changed their rolling code door openers several years ago, and you need to make sure the new keypad you bought is compatible with your opener. The old remotes are referred to as "blue button" and the new ones are "black button". If you look at the remote in your car it will have blue or black buttons, and the new keypad should state its compatible with one or the other.

Bruce

    Bookmark   April 15, 2014 at 5:46AM
Sign Up to comment
More Discussions
Sun shines on sensor....
...and garage door will not stay down! Anyone have...
phoggie
2x6 strength? How much weight will a truss in my garage hold?
I want to build an engine hoist in my garage. I found...
work.truck
Chamberlain Garage Door Opener receiver problem
For the past 5 years, my Chamberlain Whisper Drive...
clarence_locke
Easy to use Backpack Blower Storage
I have been keeping my backpack blower on the floor...
blakeas
Allister GDO not closing with remote
Having a problem with my Allister Access 3500 GDO not...
irishh7
People viewed this after searching for:
© 2015 Houzz Inc. Houzz® The new way to design your home™