Help! Need a range hood for a low ceiling (pic)

eugenie11September 4, 2011

Just posted this and the picture didn't show up, so I'm going to try again.

Here's my problem: I am replacing the range hood over my island but the distance from the ceiling to the cooktop is only 45" because of a soffit that hangs down over the island (possibly to incorporate the vent? I don't know because I can't see inside), and most of the range hoods I have looked at require more height.

Does anyone know of an island mounted range hood that will fit my specs? I would prefer one of the more low profile models, not the big hood I have now (see pic), but I realize my choices may be limited, so I'll take anything I can get!

Thanks so much in advance!

Thank you for reporting this comment. Undo
ratflinger

Why are you replacing it? If it's lack of suction then maybe an inline blower would do the trick. Bigger is better when venting. I see nothing wrong with that size of hood in your kitchen. Modernaire will make just about anything you want, but trust me - it isn't cheap.

    Bookmark   September 4, 2011 at 10:22PM
Thank you for reporting this comment. Undo
deeageaux

Elica and Futuro Futuro have some very sleak designs.

If you like the Futuro Futuro Skylight, Best offers something similar for alot cheaper.

Look through the link below.

Here is a link that might be useful: Link

    Bookmark   September 5, 2011 at 4:31AM
Thank you for reporting this comment. Undo
eugenie11

Thank you!

To ratflinger - good question! Why AM I replacing it? It works fine but everyone hates that you have to bob and weave whenever you're talking to someone across the island, I mean, it is BIG... and I thought as long as I"m updating everything else in the kitchen, I should put in a nice sleek range hood. And then I stared looking at the prices!

To deeageaux - I have looked at these designs, but when I check the specs, almost all require a minimum of 32" between the bottom edge of the hood and the top of the counter, which leaves me about six inches of chimney.

I guess I thought someone would have had the same problem and found a manufacturer who makes these short chimneys, and ... voila!

DH says I should go down to the appliance store where we just put in our order, and spent WAY too much money, and get them to help!!!

    Bookmark   September 5, 2011 at 9:10AM
Thank you for reporting this comment. Undo
sskit

Take a look at the Zephyr Anzio. We just put this in because we liked the fact that it had only a 5 1/2 inch pyramid. It has a full 24 inch capture and is 600 cfm. Reasonably priced. We are very happy with it so far. We have the wall mount unit but they have an island one.

    Bookmark   September 5, 2011 at 10:05AM
Thank you for reporting this comment. Undo
eugenie11

to sskit - zephyr's website has a spec 'calculator' that allowed me to type in my ceiling height with EVERY model they make and guess what? None will work.

But thank you. Those Zephyr hoods were my first choice - I liked Europa, and then Roma, and then I tried all the rest... Nope. None fit (sob).

    Bookmark   September 5, 2011 at 10:36AM
Thank you for reporting this comment. Undo
trixieinthegarden

Could you use an undercabinet style? You might need to add a mounting strip at the back of the soffit for the "wall" connections but it would certainly give you more options.

    Bookmark   September 5, 2011 at 2:53PM
Thank you for reporting this comment. Undo
Diplodicus

Have you considered a recessed onto the ceiling model like the gaggenau AC 402?

Dippy

    Bookmark   September 5, 2011 at 7:46PM
Thank you for reporting this comment. Undo
wpdoit

We have a low ceiling. Too low for the Monogram hood we wanted, per the installation manual. So I found the similar looking Cavaliere-Euro which is claimed to work with our approximately 7' 7" ceiling height.

Then my appliance dealer, who wanted to sell me the Monogram, said we could just have it mounted through the ceiling. So that's what the installer did, built a roughly six inch box frame between the ceiling joists, and ran the frame and shroud through the dry wall. I then put some wood trim pieces around the ceiling junction. I don't think I paid any extra for the installation.

    Bookmark   September 6, 2011 at 3:52AM
Thank you for reporting this comment. Undo
wpdoit

To add: I just measured our ceiling to cooktop height at 55 inches, which is 10 inches more than your 45. But our installer did tell me he could raise the hood through the ceiling as far as I wanted (within reason I suppose)

    Bookmark   September 6, 2011 at 4:07AM
Thank you for reporting this comment. Undo
jscout

Is there any reason you can't just trim the SS chimney of your existing or any other hood? If necessary, you can take it to a sheet metal shop and they should be able to re-fabricate it for you. It really shouldn't cost much either. Most of the time, there's nothing on those chimneys other than duct work, unless it's also hiding an inline blower. I took a look at that Zephyr site and they mention the term "out of the box." Usually, when they say that it implies that it won't fit if you don't want to customize it. The important take away is that you can probably customize it to fit.

    Bookmark   September 7, 2011 at 4:36PM
Thank you for reporting this comment. Undo
eugenie11

to trixieinthegarden - if I use an undercounter hood, don't I have to revent the whole thing? Or do all the under mounted models use recirculating vents? Right now, I have a nice arrangement that vents to the outside (I'm in a freestanding house, not an apartment) and I was hoping to keep this configuration (trying to save what remains of my budget!)

to wpdoit - after hours spent looking at every exotic brand of range hood, somehow I overlooked the good ol' GE Profile which SEEMS to work... Is my problem solved? My appliance guy is off on Wednesdays, but I am planning to call him tomorrow (and ask how we overlooked the obvious???) I'm a little nervous putting the order in because apparently range hoods are not returnable if they don't fit. Eek!

to jscout - I asked the same question - just saw off the chimney and make it fit, right? Not so fast. I was told there are all sorts of guts in there that can't just be lopped off. Who knew?

Anyway, I'm still searching - if the GE Profile fits, I'm done. If not, I may keep what I have. I never imagined I'd be spending so much time on what has to be The Most Boring appliance in the kitchen.

Thanks all! Will keep you posted

    Bookmark   September 7, 2011 at 6:32PM
Thank you for reporting this comment. Undo
weedmeister

I think that the only thing in the chimney is the flu pipe. And wiring.

How about this Kobe? It is 7" tall, the shortest vent cover is 22.75", so about 30" overall.

BTW: what is the distance now from the top of the cooktop to the bottom of the current vent? And how much from the bottom of the vent to the ceiling?

Here is a link that might be useful: Kobe IS-123

    Bookmark   September 7, 2011 at 7:10PM
Thank you for reporting this comment. Undo
wpdoit

As to modifying hoods to fit, I know the Monogram hood has the blower and a bunch of other stuff inside a two section frame work that is adjustable to an extent, by sliding the two pieces to size and using different screw holes to lock the two pieces together. The problem with our ceiling was that the adjustment range was not large enough. The duct covers just covered the main frame work structure using two sections that also slide one inside the other. We ended up using just one of the duct sections, which just fit through the ceiling by a couple of inches.

When we first opened the box containing the hood, and I was able to see everything, I felt that I could have drilled some extra holes and adjusted the frame short enough to fit to our ceiling. I do admit that when I voiced this thought, the installer looked at me like I was a little crazy.

The Profile hood I see, seems to be dimensionally and structurally very close to our Monogram. Page 13 of the installation manual has a chart showing the minimum ceiling height at 7' 11", and that I think results in the hood being 24 inches above a 36 in. counter. Maybe I'm looking at the wrong one. Model PV976NSS? eugenie, I don't think you mentioned your floor to ceiling height.

    Bookmark   September 7, 2011 at 7:17PM
Thank you for reporting this comment. Undo
eugenie11

wpdoit and weedmeister - the GE Profile model I looked at was PV977NSS, on AJ Madison. If you click on 'Specifications' it says overall height 19 and 1/8" and height to ceiling 13 and 1/4". Both of those would work for me...

Here are my dimensions: total ceiling height 89.5", aka 7' 5.5". Low. And 7.5" are in a soffit or tray that is lowered over the cooktop, possibly because of a bathtub overhead? At least that's what one contractor told me, who was looking over the job and immediately wanted to know why the ceiling was lowered over the island and what was above it ...

Distance from counter to tray ceiling: 45.5"

Distance from bottom edge of current range hood to top of counter: 22" (measuring down)

Distance from bottom edge of current range hood to tray ceiling: 23" (measuring up)

Assume that the 7.5" of tray ceiling can incorporate range hood chimney. The GE Profile model has overall height of 19 and 1/8. My current range hood has overall height of 23". Seems like it will work, right?

I have also looked at Kobe IS2236SQF, Cavaliere Euro SV218Z2-I36, and many many models of Zephyr, Broan, KitchenAid and Fridgidaire.

Also have to find out if my vent is 6" or 8" before I order. This is really one of those high-input, low-reward purchases, huh? And not even cheap!!

Thanks, guys. Keep those ideas coming!

    Bookmark   September 7, 2011 at 7:49PM
Thank you for reporting this comment. Undo
Diplodicus

Elica Cloud Nine? Flush with ceiling. I suppose I am recommending this because imho you might try to hide the ventilation and leave the space open. It would make the space seem bigger and less cramped. Not that it looks small and cramped ...it doesn't...but it might if you put a big stainless steel piece of art ventilation system in there!

Dippy

    Bookmark   September 7, 2011 at 9:32PM
Thank you for reporting this comment. Undo
eugenie11

Diplodicus - thank you! I just checked out Elica Cloud Nine online - crazy to find an artsy/enviro/philosophical company devoted to range hood designs... but I like it!

But it's past my bedtime, my brain has turned to mush from looking for induction cookware on eBay, and converting my measurements into cms to see if the range hoods will fit is just too much right now...

I will go back to the website in the morning for another look. I must be tired, I didn't even look at prices.

    Bookmark   September 7, 2011 at 11:39PM
Thank you for reporting this comment. Undo
wpdoit

Regarding the PV977NSS Profile hood, I don't know where AJ Madison gets the 19 1/2 dimension, or what it means, but on the GE website they have this;

Note the ceiling heights specified.

and from page 12 of the installation manual, they have this chart showing the minimum ceiling height to be 7' 11" whith the hood just 24 inches above a 36 inch counter top.

You can see at the top of the page that the duct covers alone are 25.98" for just the lower one (one slides inside the other to adjust overall length), and 29.92" for the upper. If it's like mine, which I am pretty sure it is, the minimum length of the vertical portion of the hood is 31 inches before you attatch the actual horizontal section to the bottom. That's why the duct covers are the length they are.

And that is why we stuck our very similiar Monogram hood almost 7" through the ceiling to give us an effective length of about 24" long (whith the hood ending up about 31 inches above the cook top.

Sorry if this is not good news, but I'm just trying to help.

    Bookmark   September 7, 2011 at 11:56PM
Thank you for reporting this comment. Undo
Diplodicus

Hi again. I just saw a neff ceiling mounted hood that you might like. The product code is 199C68N0GB. Looks great. Reasonable enough price for what it is. Integrated lights etc grease filyers remote control low noise.

Dippy

    Bookmark   September 15, 2011 at 1:41PM
Thank you for reporting this comment. Undo
trixieinthegarden

to trixieinthegarden - if I use an undercounter hood, don't I have to revent the whole thing? Or do all the under mounted models use recirculating vents? Right now, I have a nice arrangement that vents to the outside (I'm in a freestanding house, not an apartment) and I was hoping to keep this configuration (trying to save what remains of my budget!)

Most are configured to vent through the top or through the back, sometimes offering both options. If you use a top-vented one you should be able to re-use your existing venting, depending on your vent size. Most take a 6 or 8 inch duct.

The only thing that would be an issue for you is that undercabinet vent hoods usually have keyhole hangers for the back wall, so you would have to mount a strip just under your soffit at the back to mount the screws for the keyholes to hang. The vents are also attached through the bottom of the cabinet above so that takes much of the hanging weight.

    Bookmark   September 16, 2011 at 8:20PM
Thank you for reporting this comment. Undo
maire_cate

I almost hate to suggest this - but have you considered opening the tray ceiling to see what's actually there? It's really not too difficult to repair either - we've had to do it twice to move chandeliers.

    Bookmark   September 17, 2011 at 7:22AM
Sign Up to comment
More Discussions
760 cfm vs 900 cfm
I purchased a 36 Jenn Air (6 burners) range. I doubt...
abick2
Noxious new oven smell ??
Our new Electrolux wave-touch double oven is wonderful,...
infohound2006
smallest microwave (width) ever ? Please advise
I'm looking for the smallest microwave in terms of...
Pippin
Rangetops - Wolf, Bluestar Platinum, or Bluestar "regular"
I realize some of my questions have been covered, but...
riese1
Fhiaba column refrigerator freezer anyone?
Has anyone seen these in person or have in their kitchen?...
Dietitian
Sponsored Products
Chadwick Satin Nickel 47-Inch LED Three Light Billiard and Island
$690.00 | Bellacor
Lounge Floormat by Chilewich
$410.00 | Lumens
Darya Rugs Moroccan, Red, 5'0" x 7'10" M1591-478
Darya Rugs
LumenAria Rectangle 1000 Lumen LED Wall Sconce
$254.00 | Bellacor
Dale Tiffany Bathroom Lighting Knighton 3-Light Antique Golden Bronze Vanity
Home Depot
Rosy Angelis Floor Lamp by Flos Lighting
$875.00 | Lumens
Colonial Mills Market Mix Stair Tread - Oval - 8 x 28 in. - Set of 13 - MM01A008
$242.99 | Hayneedle
Brushed Steel White Cylinder Shade Plug-In Swing Arm Wall Lamp
Lamps Plus
People viewed this after searching for:
© 2015 Houzz Inc. Houzz® The new way to design your home™