Has anyone ever installed a folding RR sink?

mtnrdredux_gwOctober 27, 2013

In our new MBA, we will have two matching sinks in the main part of the bathroom. The watercloset, for lack of a better term, will also have a small sink (partly because the plumbing for it is already there, so why not.)

Anyway, the space is a tad narrow and the home is vintage, so I was looking at old folding railroad sinks. (photo below) I would not need to fold it away, but you have to, because that is how it drains.

Has anyone ever installed such a thing? I am wondering what a plumber would say, and what the visible plumbing will look like.

Thank you for reporting this comment. Undo

As for the visible plumbing , you can check restoration hardware they have 2 or 3 different kinds of drains and water supply lines that looks really nice . Good luck

Here is a link that might be useful: http://www.restorationhardware.com/catalog/product/product.jsp?productId=prod1307033&categoryId=cat1556039

    Bookmark   October 27, 2013 at 12:01PM
Thank you for reporting this comment. Undo

Dealt with dozens of them -- in railroad cars. Mostly a lot newer than the picture you show. They are made to fold into the wall and in general there is no visible plumbing. Supply and drain lines would be inside the wall. You'd need to check out the depth of the fixture versus the depth of your wall cavity to see if it would fit. Since there is no overflow, there would be a code issue in some jurisdictions.

    Bookmark   October 27, 2013 at 4:15PM
Thank you for reporting this comment. Undo

Fabulous, Moebus, thank you so much for taking the time to post! The power of Gardenweb!

    Bookmark   October 27, 2013 at 10:14PM
Thank you for reporting this comment. Undo

I actually installed one several years ago. Same type of installation. A small powder room. Teak and holly floor. Looked sharp.

The original sink I installed was designed for just a cold water supply. The owner wanted the tap water to be warmer, so I added a thermostatic valve before it (accessible, in a compartment below the sink). I had hot and cold supply lines feeding the TS mixing valve, then there was a single run of tubing from the TS valve to the sink's tap. So the water temperature was non-selectable from the folding sink itself, but it could be tweaked by the owner if needed by accessing the tempering valve in the compartment.

The temp is basically a "set and forget" type of thing.

Have your guy look for an "in-line thermostatic valve", or sometimes referred to as an "in-line tempering valve", if you want to go that route. They're around $60-$75.

The drain as well is quite simple. Standard.

To operate, you unfold the sink. Turn on the water to wash. To empty the bowl you fold it up. Water pours out the back of the bowl into the sink's housing and is funneled down the drain.

Some bowls have a deformation on the back rim of the bowl, sort of like a pouring lip on a tea pot. Probably a bad description. But the idea is that if the bowl overflows, water will outflow over the back of the rim through that spout and go down the drain.

The sink I installed did not have that feature. To comply with the overflow, I had to modify the bowl on the sink. I drilled a hole about 3/8" diameter in the top back of the bowl, about a 3/4" or so below the rim. Then I added a small piece of metal tubing, 1/2" diameter and about 3/4" long, right behind the hole. The piece of tubing acted as a chute to direct water that went through the overflow hole down the drain. Without that piece of tubing, overflow water would have simply run down the outside of the bowl and cascaded off the bottom of the bowl and on to the floor.

You'll need to add a trap. That's about it. The sink I installed was designed for the plumbing to be hidden. I hid the trap and the supply shut off valve (and the TS tempering valve) in a wall stud bay compartment behind a hidden door built in to the wall's wainscot.

If you want exposed plumbing you can do that, but be careful how it projects from the wall in relation to the sink. You can get metal tubing in myriad finishes, from rough and rustic to fine polished metal.

This post was edited by mongoct on Mon, Oct 28, 13 at 11:40

    Bookmark   October 28, 2013 at 11:31AM
Thank you for reporting this comment. Undo

Terrific, mongo, you have been so helpful. Thank you for taking the time to post.

    Bookmark   October 28, 2013 at 1:39PM
Sign Up to comment
More Discussions
Final Decisions - Lighting and Countertop - "Spa-Like" or "Dreary"?
We have been in the middle of a very long & drawn-out...
Kohler Elevance Tub - for disabled - gorgeous
Pretty new product from Kohler. anyone who is looking...
Microsilk vs. Air Tub (Jason) OR Bain Ultra
Apologies for the additional thread. I realize there...
Classic looking offset vanity top?
I'm planning out a bathroom remodel for a 1920s Craftsman...
recommend sink for combo powder/bath
am planning combo laundry/half bath. side by side washer...
Sponsored Products
Yorkshire Urn
$799.00 | FRONTGATE
Switchplates Black Steel Single Toggle/Dimmer Switch Plate
The Renovator's Supply, Inc.
Arteriors Home - Grenier Accent Table - 4140
Great Furniture Deal
Bryce Glass Mosaic Copper Sink
Signature Hardware
Cambridge Jubilee White 20 Piece Set - 07620CCP12DS
$19.99 | Hayneedle
Wedgeport Brushed Nickel Three-Light Bath Fixture
$148.00 | Bellacor
Princeton Lush Dreamax 11 in. Gel Infused Memory Foam Mattress - IDF-DM163-F
Tay Tay Chrome Three-Light Square Canopy Bath Fixture with Honey Glass
$418.50 | Bellacor
People viewed this after searching for:
© 2015 Houzz Inc. Houzz® The new way to design your home™